PIC10F200 Microchip Technology, Inc., PIC10F200 Datasheet - Page 71

• Manufacturer Part Number: PIC10F200
• Description: 6-Pin, 8-Bit Flash Microcontrollersfeatures 6-pin SOT-23 Packaging Precision 4 MHZ Internal Oscillator Baseline Core With 33 Instructions, 2 Stack Levels All Single-cycle Instructions Except For Program Branches Which Are Two Cycles 12-bit Wide
• Manufacturer: Microchip Technology, Inc.

TABLE 12-1:
 2004 Microchip Technology Inc.
DC CHARACTERISTICS
D030
D030A
D031
D032
D040
D040A
D041
D042
D070
D060
D061
D061A
D080
D080A
D090
D090A
D101
Legend:
Note 1:
Param
No.
2:
3:
4:
5:
†
*
Sym
I
V
PUR
V
I
IL
IH
IL
TBD = To Be Determined.
Data in “Typ” column is at 5V, 25 C unless otherwise stated. These parameters are for design guidance only and are
not tested.
These parameters are for design guidance only and are not tested.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Negative current is defined as coming out of the pin.
Does not include GP3. For GP3 see parameters D061 and D061A.
This specification applies to GP3/MCLR configured as external MCLR and GP3/MCLR configured as input with internal
pull-up enabled.
This specification applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the
MCLR circuit is higher than the standard I/O logic.
Input Low Voltage
I/O ports:
MCLR, T0CKI
Input High Voltage
I/O ports:
MCLR, T0CKI
GPIO weak pull-up current
Input Leakage Current
I/O ports
GP3/MCLR
GP3/MCLR
Output Low Voltage
I/O ports
Output High Voltage
I/O ports
Capacitive Loading Specs
on Output Pins
All I/O pins
DC CHARACTERISTICS: PIC10F200/202/204/206 (Industrial, Extended)
with TTL buffer
with Schmitt Trigger
buffer
with TTL buffer
with Schmitt Trigger
buffer
Characteristic
(2)
(4)
(5)
(1, 2)
(3)
Standard Operating Conditions (unless otherwise specified)
Operating temperature
Operating voltage V
+ 0.8 V
V
V
0.25 V
0.85 V
0.85 V
DD
DD
TBD
Min
Vss
Vss
Vss
Vss
2.0
—
—
—
—
—
—
– 0.7
– 0.7
Preliminary
DD
DD
DD
DD
Typ†
250
PIC10F200/202/204/206
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DD
0.15 V
0.15 V
0.15 V
Max
0.8V
TBD
± 30
V
V
V
V
range as described in DC specification
50*
± 1
± 5
0.6
0.6
—
—
DD
DD
DD
DD
DD
DD
DD
-40°C
-40°C
Units
pF
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
A
T
T
A
A
For all 4.5
Otherwise
4.5
Otherwise
For entire V
V
Vss
Vss
Vss
I
-40 C to +85 C
I
-40 C to +125 C
I
-40 C to +85 C
I
-40 C to +125 C
OL
OL
OH
OH
DD
+85°C (industrial)
+125°C (extended)
= 8.5 mA, V
= 7.0 mA, V
= -3.0 mA, V
= -2.5 mA, V
= 5V, V
V
V
V
V
DD
PIN
PIN
PIN
DD
PIN
5.5V
V
V
V
V
DD
DD
DD
DD
Conditions
range
DD
DD
= V
DD
DD
, Pin at high-impedance
= 4.5V,
= 4.5V,
5.5V
SS
= 4.5V,
= 4.5V,
DS41239A-page 69