XR1002 Mimix Broadband, XR1002 Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
XR1002
Manufacturer Part Number
XR1002
Description
GaAs MMIC Receiver
Manufacturer
Mimix Broadband
Datasheet
1.XR1002.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XR1002-QB-0N00
Manufacturer:
MIMIX
Quantity:
20 000
Part Number:
XR1002-V
Manufacturer:
MIMIX
Quantity:
20 000
18.0-34.0 GHz GaAs MMIC
Receiver
App Note [1] Biasing - As shown in the bonding diagram, this device is operated with both stages in parallel, and can
be biased for low noise performance or high power performance. Low noise bias is nominally Vd=4.5V, Id=135mA and is
the recommended bias condition. More controlled performance will be obtained by separately biasing Vd1 and Vd2
each at 4.5V, 65mA. Power bias may be as high as Vd=5.5V, Id=270mA with all stages in parallel, or most controlled
performance will be obtained by separately biasing Vd1 and Vd2 each at 5.5V, 135mA. Attenuator bias, Vg3, can be
adjusted from 0.0 to -1.2V with 0.0V providing maximum attenuation and -1.2V providing minimum attenuation. Image
reject mixer bias, Vg4, should nominally be -0.8V to minimize sensitivity of mixer performance to LO level. It is also
recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the
most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias
circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain
supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain
voltage. The typical gate voltage needed to do this is -0.5V. Typically the gate is protected with Silicon diodes to limit the
applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before
applying the positive drain supply.
App Note [2] Bias Arrangement -
For Parallel Stage Bias -- The same as Individual Stage Bias but all the drain or gate pad DC bypass capacitors
(~100-200 pF) can be combined. Additional DC bypass capacitance (~0.01 uF) is also recommended to all DC or
combination (if gate or drains are tied together) of DC bias pads.
For Individual Stage Bias -- Each DC pad (Vd1,2 and Vg1,2,3,4) needs to have DC bypass capacitance (~100-200 pF) as
close to the device as possible. Additional DC bypass capacitance (~0.01 uF) is also recommended.
MTTF Tables
These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry.
May 2006 - Rev 21-May-06
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
55 deg Celsius
75 deg Celsius
95 deg Celsius
55 deg Celsius
75 deg Celsius
95 deg Celsius
Temperature
Temperature
Backplate
Backplate
Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
101 deg Celsius
121 deg Celsius
142 deg Celsius
162 deg Celsius
182 deg Celsius
their obligation to be compliant with U.S. Export Laws.
Bias Conditions: Vd=3.0V, Id=135 mA
Bias Conditions: Vd=5.5V, Id=270 mA
81 deg Celsius
Temperature
Temperature
Channel
Channel
65.0 ° C/W
58.9 ° C/W
Rth
Rth
-
-
-
-
MTTF Hours
MTTF Hours
6.77E+11
4.09E+10
3.29E+09
4.11E+08
5.36E+07
8.35E+06
2.43E+00
1.87E+01
1.20E+02
1.48E-03
2.44E-02
3.04E-01
FITs
FITs
Page 6 of 10
R1002