ISL12027 Intersil Corporation, ISL12027 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
ISL12027
Manufacturer Part Number
ISL12027
Description
Manufacturer
Intersil Corporation
Datasheet
1.ISL12027.pdf
(27 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL12027IB27AZ
Manufacturer:
Intersil
Quantity:
669
Part Number:
ISL12027IB27AZ
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
ISL12027IB27AZ-T
Manufacturer:
SST
Quantity:
1 200
Part Number:
ISL12027IB27Z
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL12027IB27Z-T
Manufacturer:
Intersil
Quantity:
390
Company:
Part Number:
ISL12027IB30AZ-T
Manufacturer:
INTERSIL
Quantity:
3 000
Company:
Part Number:
ISL12027IBAZ-T
Manufacturer:
INTERSIL
Quantity:
4 300
Description
The ISL12027 device is a Real Time Clock with clock/
calendar, two polled alarms with integrated 512x8 EEPROM
configured in 16 Byte per page format, oscillator
compensation, CPU Supervisor (Power on Reset, Low
Voltage Sensing and Watchdog Timer) and battery backup
switch.
The oscillator uses an external, low-cost 32.768kHz crystal.
All compensation and trim components are integrated on the
chip. This eliminates several external discrete components
and a trim capacitor, saving board area and component cost.
The Real-Time Clock keeps track of time with separate
registers for Hours, Minutes, Seconds. The Calendar has
separate registers for Date, Month, Year and Day-of-week.
The calendar is correct through 2099, with automatic leap
year correction.
The Dual Alarms can be set to any Clock/Calendar value for
a match. For instance, every minute, every Tuesday, or 5:23
AM on March 21. The alarms can be polled in the Status
Register. There is a repeat mode for the alarms allowing a
periodic interrupt.
The ISL12027 device integrates CPU Supervisory functions
(POR, WDT) and Battery Switch. There is Power-On-Reset
(RESET) output with 250ms delay from power on. It will also
assert RESET when V
threshold. The V
VTS0 registers to five (5) preselected levels. There is
WatchDog Timer (WDT) with 3 selectable time-out periods
(0.25s, 0.75s and 1.75s) and disabled setting. The
WatchDog Timer activates the RESET pin when it expires.
The device offers a backup power input pin. This V
allows the device to be backed up by battery or SuperCap.
The entire ISL12027 device is fully operational from 2.7 to
5.5V and the clock/calendar portion of the ISL12027 device
remains fully operational down to 1.8V (Standby Mode).
The ISL12027 device provides 4k bits of EEPROM with 8
modes of BlockLock™ control. The BlockLock allows a safe,
secure memory for critical user and configuration data, while
allowing a large user storage area.
Pin Descriptions
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device. The input buffer on this pin is always active (not
gated). The pull-up resistor on this pin must use the same
voltage source as V
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and out
of the device. It has an open drain output and may be wire
ORed with other open drain or open collector outputs. The
input buffer is always active (not gated).
trip
DD
threshold is selectable via VTS2/VTS1/
DD
.
goes below the specified
9
BAT
pin
ISL12027
This open drain output requires the use of a pull-up resistor.
The pull-up resistor on this pin must use the same voltage
source as V
the output signal with the use of a slope controlled pull-
down. The circuit is designed for 400kHz I
speed.
V
This input provides a backup supply voltage to the device.
V
supply fails. This pin can be connected to a battery, a
SuperCap or tied to ground if not used.
RESET
The RESET signal output can be used to notify a host
processor that the watchdog timer has expired or the V
voltage supply has dipped below the V
an open drain, active LOW output. Recommended value for
the pull-up resistor is 10kΩ. If unused it can be tied to
ground.
X1, X2
The X1 and X2 pins are the input and output, respectively, of
an inverting amplifier. An external 32.768kHz quartz crystal
is used with the ISL12027 to supply a timebase for the real
time clock. Internal compensation circuitry provides high
accuracy over the operating temperature range from
-40°C to +85°C. This oscillator compensation network can
be used to calibrate the crystal timing accuracy over
temperature either during manufacturing or with an external
temperature sensor and microcontroller for active
compensation. X2 is intended to drive a crystal only, and
should not drive any external circuit (Figure 11).
NO EXTERNAL COMPENSATION RESISTORS OR
CAPACITORS ARE NEEDED OR ARE RECOMMENDED
TO BE CONNECTED TO THE X1 AND X2 PINS.
Real Time Clock Operation
The Real Time Clock (RTC) uses an external 32.768kHz
quartz crystal to maintain an accurate internal representation
of the second, minute, hour, day, date, month, and year. The
RTC has leap-year correction. The clock also corrects for
months having fewer than 31 days and has a bit that controls
24 hour or AM/PM format. When the ISL12027 powers up
after the loss of both V
operate until at least one byte is written to the clock register.
BAT
BAT
FIGURE 11. RECOMMENDED CRYSTAL CONNECTION
supplies power to the device in the event the V
DD
. The output circuitry controls the fall time of
DD
and V
BAT
X1
X2
, the clock will not
RESET
2
C interface
threshold. It is
April 17, 2006
DD
FN8232.3
DD