T15L256A TM tech, T15L256A Datasheet
T15L256A
Related parts for T15L256A
T15L256A Summary of contents
Page 1
... X 8 LOW POWER CMOS STATIC RAM GENERAL DESCRIPTION The T15L256A is a high speed, low power CMOS static RAM organized as 32,768 x 8 bits that operates on a single 3.3-volt power supply. This device is packaged in standard 28-pin 300 mil SOJ , 28-pin SOP, TSOP-I forward ...
Page 2
... 8.0mA 4.0mA I/O=0mA IL Cycle = MIN. Duty = 100 Cycle=MIN, Duty=100 -0.2V,f=0MHz P. 2 T15L256A UNIT MAX UNIT 3.3 Typ+5% - 0.8 - Vcc+0 I/O1- I/O8 Vcc I I High-Z SB1 SB, High-Z Icc Data Out Icc Data In Icc MIN. ...
Page 3
... I /O OUT 1.5V C =30pF ohm 3.3V OUTPUT R2 350 ohm (For CLZ 3.0V 90% 90 10% 10% 3ns Fig T15L256A MAX. UNIT CONDITIONS -4mA/8mA ohm ohm Vt =1.5V Fig.3 R1 320 ohm R2 5pF 350 Including ohm ...
Page 4
... MIN. MAX WHZ OHZ T15L256A T15M256A-70 UNIT MIN. MAX T15M256A-70 UNIT MIN. MAX ...
Page 5
... T15L256A DON 'T CAR E UN DEF IN ED Publication Date: APR. 2001 Revision:C ...
Page 6
... Fixed T15L256A CAR INE D Publication Date: APR. 2001 Revision: C ...
Page 7
... OUT C 500 mV from steady state with is high during a controlled write cycle, this requirement does not T15L256A D during the write cycle 5pF. This parameter is L Publication Date: APR. 2001 Revision: C ...
Page 8
... N 0.268±0.003 O 0.300±0.002 P 0.053±0.001 Q 0.140±0.004 y 0.004(MAX) Taiwan Memory Technology, Inc. reserves the right to change products or specifications without notice. T15L256A DIMENSIONS IN MM 18.03±0.05 7.62±0.13 1.52±0.05 1.27±0.03 1.63±0.03 0.38±0.05 0.76±0.05 1.27±0.05 0.46±0.05 0.71±0.05 8.56±0.05 0.25± ...
Page 9
... DIMENSIONS IN INCHES 0.047(max.) 0.004±0.002 0.039 ± 0.002 0.008(typ.) 0.006(typ.) 0.465 ± 0.004 0.315 ± 0.004 0.022(typ.) 0.528 ± 0.008 0.020 ± 0.004 0.0315 ± 0.004 0.004(max T15L256A Seating plane y A 0.010 L L1 DIMENSIONS IN MM 1.20(max.) 0.10± ...
Page 10
... P. 10 T15L256A e1 Detail See Detail F Notes : 1. Dimensions D max. & S include mold flash or tie bar burrs. 2. Dimension b does not include dambar protrusion / intrusion. 3. Dimensions D & E include mold mismatch and determined at the mold parting line. 4. controlling dimension : inches 5. general appearance spec should be based on final visual inspection spec ...