UPD160083 NEC, UPD160083 Datasheet
![no-image](/images/manufacturer_photos/0/4/470/nec_sml.jpg)
UPD160083
Related parts for UPD160083
UPD160083 Summary of contents
Page 1
... Because the output dynamic range is as large as V operation of the LCD’s common electrode is rendered unnecessary. Also able to deal with dot-line inversion, n-line inversion and column line inversion when mounted on a single side, this source driver is equipped with a built- in 8-bit D/A converter circuit whose odd output pins and even output pins respectively output gray scale voltages of differing polarity ...
Page 2
BLOCK DIAGRAM STHR R,/L CLKP, CLKN STB 00P 03P 00N 03N 10P 13P 10N 13N 20P 23P 20N ...
Page 3
... RPI1 Remark 1. This figure does not specify the TCP package recommended to connect to analog GND on PCB for the return current of transmission line. SS1A And please don’t use these pins for power supply terminal with dynamic current. Preliminary Product Information S16450EJ1V0PM00 ...
Page 4
... The display data is input with a width of 12 bits by double edge, viz., the gray scale data (8 bits dots (1 pixel). Input These refer to the start pulse input/output pins when driver ICs are connected in cascade. The shift directions of the shift registers are as follows. R,/ ...
Page 5
... F is also advised between the - corrected power supply pins (V 3. Because of the large power consumption of this driver IC necessary to pay attention to the driver IC's temperature for the Junction Temperature. So, it should be considered to use the suitable mechanical design for the heat spreading and use the LPC function and the output reset function for the power reduction ...
Page 6
RELATIONSHIP BETWEEN INPUT DATA AND OUTPUT VOLTAGE VALUE The PD160083 incorporates a 8-bit D/A converter whose odd output pins and even output pins output respectively gray scale voltages of differing polarity with respect to the LCD’s counter electrode (common ...
Page 7
... V ’ 253 r253 ’ 7 254 r254 r255 ’ 255 Caution There is no connection between V Preliminary Product Information S16450EJ1V0PM00 -corrected Voltages and Ladder Resistors Ratio V ’’ 255 rn Ratio Value rn Ratio r0 31.50 630 r64 2.25 r1 27.50 550 r65 2.25 r2 24.00 480 r66 2 ...
Page 8
Figure 4 3. Relationship between Input Data and Output Voltage (1/2) (Output voltage 1) V DD2 O utput Voltage Data Data 00H V0' V0 40H V64' V3 01H V1' V1 41H V65' V3+(V4-V3) X 02H V2' V1+(V2-V1) X 42H V66' ...
Page 9
Figure 4 3. Relationship between Input Data and Output Voltage (2/2) (Output voltage 2) 0.5 V DD2 Output Voltage Data Data 00H V0" V17 40H V64" V14 01H V1" V16 41H V65" V14+(V13-V14) X 02H V2" V16+(V15-V16) X 550 / ...
Page 10
RELATIONSHIP BETWEEN INPUT DATA AND OUTPUT PIN Data format: 8 bits 1 RGB (3 dots) Input width: 12 bits x double edge (1-pixel data) (1) R,/ (Right shift) Output Data ...
Page 11
TIMING CHART AND RELATIONSHIP BETWEEN 8-BIT DATA AND DATA BUS LINE CLK (Differential) STHR D 00 (Differential (Differential (Differential (Differential (Differential (Differential (Differential (Differential) D ...
Page 12
RELATIONSHIP BETWEEN MODE, STB, POL, MODE1 to MODE3 AND OUTPUT WAVEFORM The PD160083 has a various kind of output short function that can be controlled by MODE1 to MODE3. Please refer to the following description of each function and ...
Page 13
MODE1 = L, MODE2 = H or open Output short function works during STB = H at this mode. So all outputs are started at the falling edge of STB (See figure 8 2). But output short function works ...
Page 14
MODE1 = L, MODE2 = L All output always become Hi-Z condition during STB = H in this mode. And output short function works at the falling edge of STB during requested period by MODE3. At MODE3 = H, ...
Page 15
ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (T = +25 ° Parameter Symbol Logic Part Supply Voltage V DD1D Driver Part Supply Voltage V DD2 Logic Part Input Voltage V I1 Driver Part Input Voltage V I2 Logic Part ...
Page 16
Electrical Characteristics (T = –10 to +75 ° Parameter Symbol Input Leak Current I IL High-Level Output Voltage V STHR (STHL Low-Level Output Voltage V STHR (STHL -Corrected Resistance R V DD2 V -V ...
Page 17
Switching Characteristics (T = –10 to +75 ° Parameter Symbol Start Pulse Delay Time t PLH1 Note1 Driver Output Delay Time t PLH2 Note2 t PLH3 Note1 t PHL2 Note2 t PHL3 Note1 t PLH4 Note2 t PLH5 ...
Page 18
Timing Requirement (T = –10 to +75° 1.0 ns (RSDS Parameter Symbol Clock Period PW CLK Clock Pulse High Period PW CLK(H) Clock Pulse Low Period PW CLK(L) Data Setup Time t ...
Page 19
...
Page 20
...
Page 21
... The following conditions must be met for mounting conditions of the PD160010. For more details, refer to the [Semiconductor Device Mount Manual] (http://www.necel.com/pkg/en/mount/index.html) Please consult with our sales offices in case other mounting process is used case the mounting is done under different conditions. ...
Page 22
... HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction connection is provided to the input pins possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry ...