LTC3529 Linear Dimensions Semiconductor, LTC3529 Datasheet - Page 9

no-image

LTC3529

Manufacturer Part Number
LTC3529
Description
1.5MHz Step-Up dc
Manufacturer
Linear Dimensions Semiconductor
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC3529EDCB
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3529EDCB
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3529EDCB#PBF
Manufacturer:
LT
Quantity:
4 600
Part Number:
LTC3529EDCB#TRMPBF
Manufacturer:
MOELLER
Quantity:
6 000
Part Number:
LTC3529EDCB#TRMPBF
Manufacturer:
LINEAR进口
Quantity:
20 000
Part Number:
LTC3529EDCB#TRPBF
Manufacturer:
LT
Quantity:
4 500
www.datasheet4u.com
APPLICATIONS INFORMATION
Inductor Selection
The LTC3529 can utilize small surface-mount chip induc-
tors due to its fast 1.5MHz switching frequency. Larger
values of inductance will allow slightly greater output
current capability by reducing the inductor ripple current.
Increasing the inductance above 10μH will increase com-
ponent size while providing little improvement in output
current capability.
USB On-The-Go specifi cations limit output capacitance to
6.5μF . When using a 6.5μF output capacitance, a 4.7μH
inductor must be used to maintain stability. Larger induc-
tors may be used with larger output capacitors.
The minimum inductance value for a given allowable induc-
tor ripple ΔI (in Amps peak-to-peak) is given by:
where V
operating frequency in MHz (1.5MHz Typ), and V
the output voltage (5V).
The inductor current ripple is typically set for 20% to 40%
of the maximum inductor current (I
ferrite core inductor materials reduce frequency depen-
dent power losses compared to cheaper powdered iron
cores, improving effi ciency. To achieve high effi ciency, a
low ESR inductor should be utilized. The inductor must
have a saturation current rating greater than the worst
case average inductor current plus half the ripple current.
Molded chokes and some chip inductors usually do not have
enough core to support peak LTC3529 inductor currents.
To minimize radiated noise, use a shielded inductor. See
Table 2 for suggested components and suppliers.
Table 2. Representative Surface Mount Inductors
MANUFACTURER PART NUMBER VALUE
Sumida
TDK
Coilcraft
Cooper Bussmann SD25-4R7
L
>
V
IN MIN
IN(MIN)
(
)
Δ
CDRH5D16NP
VLF5014S
MSS6122
I f V
is the minimum input voltage, f is the
(
• •
V
OUT
OUT
V
IN MIN
(
(μH)
4.7
4.7
4.7
4.7
)
)
µH
CURRENT
MAX
P
2.15
1.82
(A)
2.3
). High frequency
2
0.064
0.098
0.065
0.043
DCR
(Ω)
OUT
HEIGHT
(mm)
1.8
1.4
2.2
2.5
is
PCB Layout Guidelines
The LTC3529 switches large currents at high frequencies.
Special care should be given to the PCB layout to ensure
stable, noise-free operation. Figure 1 depicts the recom-
mended PCB layout to be utilized for the LTC3529. A few
key guidelines follow:
1. All circulating current paths should be kept as short
2. The PGND pin should be shorted directly to the ex-
3. All the external components shown in Figure 1 and their
4. Use of multiple vias in the die attach pad will enhance
as possible. This can be accomplished by keeping the
copper traces to all components in Figure 1 short and
wide. Capacitor ground connections should via down
to the ground plane in the shortest route possible. The
bypass capacitors on V
close to the IC and should have the shortest possible
paths to ground.
posed pad, as shown in Figure 1. This provides a single
point connection between the small signal ground and
the power ground, as well as a wide trace for power
ground.
connections should be placed over a complete ground
plane.
the thermal environment of the converter, especially if
the vias extend to a ground plane region on the exposed
bottom surface or inner layers of the PCB.
Figure 1. LTC3529 Recommended PCB Layout
SHDN
PGND
V
OUT
SW
1
2
3
4
TO GROUND PLANE
MULTIPLE VIAs
IN
and V
OUT
8
7
6
5
LTC3529
should be placed
V
RST
SNSGND
FAULT
IN
3529fa
9

Related parts for LTC3529