NL128102BC29_10 NEC, NL128102BC29_10 Datasheet
NL128102BC29_10
Available stocks
Related parts for NL128102BC29_10
NL128102BC29_10 Summary of contents
Page 1
... DOD-PP-0492 (2nd edition) This PRELIMINARY DATA SHEET is updated document from DOD-PP-0486(1) All information is subject to change without notice. Please confirm the sales representative before starting to design your system. 1 © NEC LCD Technologies, Ltd. 2008 All rights reserved. Datasheet pdf - http://www.DataSheet4U.net/ ...
Page 2
... No part of this document will be used, reproduced or copied without prior written consent of NEC. NEC does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. No license, express or implied, is granted under any patent, copyright or other intellectual property right of NEC ...
Page 3
... ELECTRICAL CHARACTERISTICS...................................................................................................8 4.3.1 LCD panel signal processing board ...............................................................................................8 4.3.2 Backlight lamp ...............................................................................................................................9 4.3.3 Power supply voltage ripple......................................................................................................... 11 4.3.4 Fuse.............................................................................................................................................. 11 4.4 POWER SUPPLY VOLTAGE SEQUENCE ........................................................................................12 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS.........................................................13 4.5.1 LCD panel signal processing board .............................................................................................13 4.5.2 Backlight lamp .............................................................................................................................14 4.5.3 Positions of plug and socket ........................................................................................................15 4.6 SELECTION OF LVDS DATA INPUT MAP ......................................................................................16 4.6.1 Mode A ........................................................................................................................................16 4 ...
Page 4
OUTLINE 1.1 STRUCTURE AND PRINCIPLE Color LCD module NL128102BC29-10 is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and ...
Page 5
GENERAL SPECIFICATIONS Display area Diagonal size of display Drive system Display color Pixel Pixel arrangement Dot pitch Pixel pitch Module size Weight Contrast ratio Viewing angle Designed viewing direction Polarizer surface Polarizer pencil-hardness Color gamut Response time Luminance ...
Page 6
... Note1: Relations between GND (Signal ground), FG (Frame ground) and VBLC (Lamp low voltage terminal) in the LCD module are as follows. GND - FG GND - VBLC FG - VBLC Note2: GND and FG must be connected to customer equipment's ground, and it is recommended that GND, FG and customer inverter ground are connected together in customer equipment. Power DC/DC supply ...
Page 7
DETAILED SPECIFICATIONS 4.1 MECHANICAL SPECIFICATIONS Parameter Module size Display area Weight Note1: Excluding lamp cable, cable clamp and projections. Note2: See "7. OUTLINE DRAWINGS". 4.2 ABSOLUTE MAXIMUM RATINGS LCD panel signal processing board Power supply voltage Input voltage ...
Page 8
ELECTRICAL CHARACTERISTICS 4.3.1 LCD panel signal processing board Parameter Power supply voltage Power supply current Permissible ripple voltage Differential input threshold voltage Terminating resistance Input voltage for TxSEL signal Input current for TxSEL signal Note1: Checkered flag pattern ...
Page 9
Backlight lamp Parameter Lamp current Lamp voltage Lamp starting voltage Lamp oscillation frequency Note1: This product consists of 6 backlight lamps, and these specifications are for each lamp. Note2: The lamp voltage cycle between lamps should be kept ...
Page 10
... Note6: In case of Inverter with Ballast condenser, "VS" is the voltage level between Ballast condenser and Connector (Refer to the below “Example of measurement”). "VS" should be designed to be more than minimum "VS". Otherwise the lamp may not be turned on because the lamp starting voltage is less than minimum " ...
Page 11
Power supply voltage ripple This product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. Power supply voltage VDD Note1: The permissible ...
Page 12
POWER SUPPLY VOLTAGE SEQUENCE VDD Note1 0V Display signals* TxSEL signal Note2 10ms < t < 35ms 10ms < t < 35ms * These signals should be measured at the terminal of 100 Ω resistance. Note1: In terms ...
Page 13
... Note1: Twist pair wires with 100Ω (Characteristic impedance) should be used between LCD panel signal processing board and LVDS transmitter. Note2: All GND and VDD terminals should be used without any non-connected lines. Note3: TxSEL is pulled-up in the product. (Pull-up resistance: 50kΩ) Note4: See " ...
Page 14
... Backlight lamp Attention: VBLH and VBLC must be connected correctly. Wrong connections will cause electric shock and also break down of the product. CN201 plug (LCD module side): BHSR-02VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: Pin No. Symbol 1 VBLH 2 VBLC CN202 plug (LCD module side): BHSR-02VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: Pin No ...
Page 15
Positions of plug and socket 1 CN201 2 1 CN202 2 1 CN203 2 1 CN204 2 1 CN205 2 1 CN206 2 Rear side 1 Insert direction PRELIMINARY DATA SHEET DOD-PP-0492 (2nd edition) NL128102BC29-10 CN1 30 15 ...
Page 16
SELECTION OF LVDS DATA INPUT MAP 4.6.1 Mode A Input data Note3 RSVD Note3 RSVD Note3 RSVD Note3 RSVD Note3 RSVD Note3 RSVD Note3 RSVD Transmitter Note1 DS90CF383, C385 or equivalent Pin → RA0 51 TXIN0 → RA1 ...
Page 17
Mode B Input data Note1 → RA2 → RA3 → RA4 → RA5 → RA6 → RA7 → GA2 → GA3 → GA4 → GA5 → GA6 → GA7 → BA2 → BA3 → BA4 → BA5 → ...
Page 18
Note1: LSB (Least Significant Bit) – RA0, GA0, BA0, RB0, GB0, BB0 MSB (Most Significant Bit) – RA7, GA7, BA7, RB7, GB7, BB7 Note2: Twist pair wires with 100Ω (Characteristic impedance) should be used between LCD panel signal processing ...
Page 19
DISPLAY POSITION D ( D(1, 1) D(1, 2) • • • • • • D(1,1024) 4.9 INPUT SIGNAL TIMINGS 4.9.1 Timing characteristics Parameter CLK Rise time, Fall time CLK-DATA DATA Rise time, Fall time ...
Page 20
Input signal timing chart Horizontal timing DATA (A) Note1 DATA (B) Vertical timing DATA (A), (B) tc CLK INVALID 1 INVALID 2 DE INVALID Note1: DATA (A) = RA0-RA7, GA0-GA7, BA0-BA7 DATA (B) = ...
Page 21
OPTICS 4.10.1 Optical characteristics Parameter Luminance θR = 0°, θL = 0°, θU = 0°, θD = 0° Contrast ratio θR = 0°, θL = 0°, θU = 0°, θD = 0° Luminance uniformity θR = 0°, θL ...
Page 22
Definition of contrast ratio The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = 4.10.3 Definition of luminance uniformity The luminance uniformity is calculated by using following formula. Luminance uniformity (LU) = The luminance ...
Page 23
RELIABILITY TESTS Test item High temperature and humidity (Operation) Heat cycle (Operation) Thermal shock (Non operation) Vibration (Non operation) Mechanical shock (Non operation) ESD (Operation) Dust (Operation) Low pressure Note1: Display functions are checked under the same conditions ...
Page 24
PRECAUTIONS 6.1 MEANING OF CAUTION SIGNS The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS" and "6.3 ATTENTIONS", after understanding these contents! This sign has the meaning that customer will be injured by ...
Page 25
... Properly connect the plug (backlight side) to adaptable socket (inverter side) without incomplete connection. After connecting, be careful not to hook the lamp cables because incomplete connection may occur by hooking the lamp cables. This incomplete connection may cause abnormal operation of high voltage circuit. ...
Page 26
... In this case, power should be supplied again. 6.3.4 Other ① All GND and VDD terminals should be used without any non-connected lines. ② Do not disassemble a product or adjust variable resistors. ③ Pack the product with original shipping package, in order to avoid any damages during transportation, when returning the product to NEC for repair and so on. ④ ...
Page 27
OUTLINE DRAWINGS 7.1 FRONT VIEW Note1: The torque for product mounting screws must never exceed 0.67N⋅m. And the length of product mounting screws from surface of plate(product side) must be 4.0mm to 7.0mm. Note2: Excluding lamp cable, cable clamp ...
Page 28
REAR VIEW Note1: The values in parentheses are for reference. Note2: The cable of up side and down side is the same length. PRELIMINARY DATA SHEET DOD-PP-0492 (2nd edition) NL128102BC29-10 Unit ...
Page 29
... New issue Writer Approved by Checked by T. OGAWA Revision contents P5 General specifications • Restonse time: (16) ms(typ.) → (20) ms(typ.) P6 Block diagram • GND-FG: Not connected → Connected Electrical characteristics P9 - Backlight lamp → (300)cd/m • Lamp current: 300cd/m 2 P11 Fuse • Rating: (4.0A), (25V) → (2.5A), (32V) • ...