rf5111 RF Micro Devices, rf5111 Datasheet
![no-image](/images/manufacturer_photos/0/5/562/rf_micro_devices_sml.jpg)
rf5111
Available stocks
Related parts for rf5111
rf5111 Summary of contents
Page 1
... The device is self-contained with 50Ω input and the output can be easily matched to obtain optimum power and efficiency characteris- tics. The RF5111 can be used together with the RF5110 for dual-band operation. The device is packaged in an ultra-small plastic package, minimizing the required board space ...
Page 2
... RF5111 Absolute Maximum Ratings Parameter Supply Voltage Power Control Voltage (V ) APC Enable Voltage (V ) AT_EN DC Supply Current Input RF Power Duty Cycle at Max Power Output Load VSWR Operating Case Temperature Storage Temperature Parameter Min. Overall Operating Frequency Range Usable Frequency Range Maximum Output Power +32 ...
Page 3
... V 4.8 V 5.5 V 1.3 A 295 mA μ μ RF5111 Condition Maximum P , Voltage supplied to the input OUT Minimum P , Voltage supplied to the input OUT V =0.3V to 2.8V, V =2.7V, AT_EN APC1,2 P =+8dBm IN P =-10dBm to +33dBm OUT DC to 2MHz V =2.8V APC1,2 V =0V APC1,2 Specifications Nominal operating limits, P < ...
Page 4
... RF5111 Pin Function Description 1 VAT EN Control pin for the pin diode. The purpose of the pin diode is to attenuate RF drive level when V the device caused by self-biasing under high RF drive levels. A good input match is maintained when the input stage bias is turned off by the same mechanism ...
Page 5
... RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A1 DS060921 Package Drawing 0. -A- 1.00 2 PLCS 3.00 SQ. 0.85 1.50 TYP 0.80 0.65 2 PLCS 0. 12° MAX -B- 1.37 TYP Dimensions in mm. 2.75 SQ. 2 PLCS 0. 0.60 0.30 0.24 0.18 TYP 0.45 0.00 4 PLCS 0.23 0.13 4 PLCS 0.55 0.30 0.50 RF5111 Interface Schematic VCC2 From Bias GND2 Stages Same as pin 14. Same as pin 14. 0.05 C 0.05 0.01 SEATING PLANE -C- 1.65 SQ. 1. ...
Page 6
... RF5111 Theory of Operation and Application Information The RF5111 is a three-stage device with 28 dB gain at full power. Therefore, the drive required to fully saturate the output is +5dBm. Based upon HBT (Heterojunction Bipolar Transistor) technology, the part requires only a single positive 3V supply to operate to full specification. Power control is provided through a single pin interface, with a separate Power Down control pin. ...
Page 7
... High current conditions are potentially dangerous to any RF device. High currents lead to high channel temperatures and may force early failures. The RF5111 includes temperature compensation circuits in the bias network to stabilize the RF transistors, thus limiting the current through the amplifier and protecting the devices from damage. The same mechanism works to com- pensate the currents due to ambient temperature variations ...
Page 8
... RF5111 Distance between edge of device and capacitor is 0.240" to improve the "off" isolation 15 pF 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com Application Schematic Instead of a stripline, an inductor ...
Page 9
... Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A1 DS060921 Internal Schematic VCC1 APC1 VCC 500 Ω 320 Ω 2.5k Ω 2.5k Ω GND1 RF5111 VCC2 RF OUT APC2 VCC 200 Ω 1.5k Ω PKG BASE PKG BASE ...
Page 10
... RF5111 Dual-Band DCS/PCS Lumped Element VAT EN C25 C24 Ω μstrip 1.2 nH VCC 100 mils C3 C3A 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. ...
Page 11
... Board Thickness 0.032”, Board Material FR-4, Multi-Layer 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A1 DS060921 Evaluation Board Layout Board Size 2.0” x 2.0” RF5111 ...
Page 12
... Pulse Generator Notes about testing the RF5111 The test setup shown above includes two attenuators. The 3dB pad at the input is to minimize the effects that the switching of the input impedance of the PA has on the signal generator. When V change can cause the signal generator to vary its output signal, either in output level or in frequency. Instead of an attenuator an isolator may also be used ...
Page 13
... Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A1 DS060921 PCB Design Requirements A = 0.64 x 0.28 (mm) Typ 0.28 x 0.64 (mm) Typ 1.50 (mm) Sq. Dimensions in mm. 1.50 Typ. 0.50 Typ. Pin Pin Pin 8 0.55 Typ. 0.75 Typ. RF5111 Pin 12 0.75 Typ. 1.50 Typ ...
Page 14
... RF5111 PCB Solder Mask Pattern Liquid Photo-Imageable (LPI) solder mask is recommended. The solder mask footprint will match what is shown for the PCB metal land pattern with a 2mil to 3mil expansion to accommodate solder mask registration clearance around all pads. The center-grounding pad shall also have a solder mask clearance. Expansion of the pads to create solder mask clearance can be provided in the master data or requested from the PCB fabrication supplier ...