fb2t-000z IDEC Corporation, fb2t-000z Datasheet - Page 7

• Manufacturer Part Number: fb2t-000z
• Description: Fb Series Plastic Control Boxes
• Manufacturer: IDEC Corporation

(06/07/04)
• Determine the panel thickness by excluding the thickness of the
• Do not expose the cable to excessive force, otherwise failure or
• Determine the mounting hole centers referring to the dimensions
Mounting Bracket
Hook Mounting
• Attach the FB9Z-PK1 mounting
• Do not tighten the FB9Z-PK1 onto
• When using the FB9Z-PK1 as hook mounting brackets, make sure
• Make sure that the mounting strength is secured.
Frame Mounting
• The FB9Z-PK1 can be used as
• Attach the FB9Z-PK1 on the FB
• Do not tighten the FB9Z-PK1 onto
• Using two M6 screws, fasten the
• Do not expose the FB series to excessive force, otherwise failure
• Make sure that the mounting strength is secured in consideration
base (2.0 mm) and accessories (if used) from the maximum panel
thickness for the control unit.
damage may be caused. When mounting strength is needed,
insert M4 tapping screws from the front of the panel (screw tight-
ening depth: 8 to 10mm / tapping screw hole: ø3.7mm)
of the contact cover box on page 4.
bracket on the FB series with the
supplied screws (two M4 tapping
screws).
Recommended tightening torque:
1.3±0.1 N·m
the FB series with excessive force.
The tapping screw hole may be
damaged and may not securely hold the control box.
that vibrations or shocks do not cause the control box to fall off,
and that the control unit operates properly.
frame mounting brackets by attach-
ing two FB9Z-PK1 as shown at
right.
series with the supplied screws (two
M4 tapping screws).
Recommended tightening torque:
1.3±0.1 N·m.
the FB series with excessive force.
The tapping screw hole may be
damaged and may not securely
hold the control box.
FB9Z-PK1 securely on the frame.
Recommended tightening torque: 5.0±0.3 N·m
∗ M6 mounting screws and nuts are not supplied with the FB9Z-PK1.
∗ The value of the recommended tightening torque for M6 screws has been
or damage may be caused.
of the operation of control unit.
Instructions
confirmed with a hexagon socket head screw. When other screws are
used and tightened to a smaller torque, make sure that the screws do not
become loose after mounting.
Rubber Gasket
Operator
Nameplate
Panel
FB9Z-PK1
Rubber Gasket (supplied)
Base
Nut
Frame
M6 Screw
Four M4 Tapping Screw Holes
Two M4 Tapping Screw Holes
Locking Ring
Contact Block
FB9Z-PK1
Two M4 Tapping
Screws (supplied)
Two M4 Tapping
Screws (supplied)
Cover
FB9Z-PK1
Dimensions
DIN Rail Adapter
Installing the FB9Z-PK3 DIN Rail Adapter
• To attach the FB9Z-PK3 on the FB series, position the positioning
• Do not tighten the FB9Z-PK3 onto the FB series with excessive
Installing the DIN Rail
• To attach a DIN rail, use plain
• DIN rail mounting screw (M5)
FB
<FB9Z-PK1>
L
A
B
L
C
D
hole of the FB9Z-PK3 with the positioning boss in the control box
using four M3 tapping screws (supplied) as shown in the figure
below. Recommended tightening torque: 0.9±0.1 N·m
force. The tapping screw hole may be damaged and may not
securely hold the control box.
washers and spring washers on
two M5 screws and tighten
firmly.
Recommended tightening
torque: 2.0±0.1 N·m
Screw length: (spring washer
thickness + plain washer thick-
ness + DIN rail thickness) + 3 to
5 mm
FB1
12.5
FB1
114
76
19
76
93
FB Series Control Box
FB Series Control Box
Series
72
36
30
FB2
18.5
FB2
140
140
156
177
12
Plastic Control Boxes
FB3
18.5
FB3
200
200
216
237
12
<Frame Mounting>
<Hook Mounting>
✩36
76
76
Mounting Hole
✩ Adjustable range
M6 Screw
All dimensions in mm.
Positioning Boss
FB9Z-PK3
Positioning Hole
DIN Rail
Two M5 Screws
(including spring
washer and plaing
washer)
Four M3 Tapping
Screws (supplied)
59.5
59.5
10
10
7