isl6252a Intersil Corporation, isl6252a Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
isl6252a
Manufacturer Part Number
isl6252a
Description
Highly Integrated Battery Charger Controller For Notebook Computers
Manufacturer
Intersil Corporation
Datasheet
1.ISL6252A.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
isl6252aHAZ
Manufacturer:
HITACHI
Quantity:
6 221
Part Number:
isl6252aHAZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Typical Operating Performance
Functional Pin Descriptions
BOOT
Connect BOOT to a 0.1µF ceramic capacitor to PHASE pin
and connect to the cathode of the bootstrap Schottky diode.
UGATE
UGATE is the high side MOSFET gate drive output.
LGATE
LGATE is the low side MOSFET gate drive output; swing
between 0V and VDDP.
PHASE
The Phase connection pin connects to the high side
MOSFET source, output inductor, and low side MOSFET
drain.
CSOP/CSON
CSOP/CSON is the battery charging current sensing
positive/negative input. The differential voltage across CSOP
and CSON is used to sense the battery charging current,
and is compared with the charging current limit threshold to
regulate the charging current. The CSON pin is also used as
the battery feedback voltage to perform voltage regulation.
CSIP/CSIN
CSIP/CSIN is the AC adapter current sensing
positive/negative input. The differential voltage across CSIP
and CSIN is used to sense the AC adapter current, and is
compared with the AC adapter current limit to regulate the
AC adapter current.
GND
GND is an analog ground.
DCIN
The DCIN pin is the input of the internal 5V LDO. Connect it
to the AC adapter output. Connect a 0.1µF ceramic
capacitor from DCIN to CSON.
11
FIGURE 16. TRICKLE TO FULL-SCALE CHARGING
DCIN = 20V, 4S2P Li-Battery, T
ISL6252, ISL6252A
ACSET
ACSET is an AC adapter detection input. Connect to a
resistor divider from the AC adapter output.
ACPRN
Open-drain output signals AC adapter is present. ACPRN
pulls low when ACSET is higher than 1.26V; and pulled high
when ACSET is lower than 1.26V.
EN
EN is the Charge Enable input. Connecting EN to high
enables the charge control function, connecting EN to low
disables charging functions. Use with a thermistor to detect
a hot battery and suspend charging.
ICM
ICM is the adapter current output. The output of this pin
produces a voltage proportional to the adapter current.
PGND
PGND is the power ground. Connect PGND to the source of
the low side MOSFET.
VDD
VDD is an internal LDO output to supply IC analog circuit.
Connect a 1μF ceramic capacitor to ground.
VDDP
VDDP is the supply voltage for the low-side MOSFET gate
driver. Connect a 4.7Ω resistor to VDD and a 1μF ceramic
capacitor to power ground.
ICOMP
ICOMP is a current loop error amplifier output.
VCOMP
VCOMP is a voltage loop amplifier output.
CELLS
This pin is used to select the battery voltage. CELLS = VDD
for a 4S battery pack, CELLS = GND for a 3S battery pack,
CELLS = Float for a 2S battery pack.
A
= +25°C, Unless Otherwise Noted. (Continued)
CHARGE
CURRENT
1A/div
CHLIM
1V/div
July 19, 2007
FN6498.1