adc122s655cimmx National Semiconductor Corporation, adc122s655cimmx Datasheet
adc122s655cimmx
Related parts for adc122s655cimmx
adc122s655cimmx Summary of contents
Page 1
... MHz to 16 MHz. The ADC122S655 is available in a 10-lead MSOP pack- age. Connection Diagram TRI-STATE® trademark of National Semiconductor Corporation. MICROWIRE™ trademark of National Semiconductor Corporation. QSPI™ and SPI™ are trademarks of Motorola, Inc. © 2008 National Semiconductor Corporation Features ■ ...
Page 2
... Ordering Information Order Code Temperature Range ADC122S655CIMM −40°C to +105°C ADC122S655CIMMX −40°C to +105°C ADC122S655EB Block Diagram www.national.com Description 10-Lead MSOP Package, 1000 Units Tape & Reel 10-Lead MSOP Package, 3500 Units Tape & Reel Evaluation Board 2 Top Mark ...
Page 3
Pin Descriptions and Equivalent Circuits Pin No. Symbol V 1 REF 2 CHA+ 3 CHA− 4 CHB− 5 CHB+ 6 GND OUT 9 SCLK 10 CS Description Voltage Reference Input. A voltage reference between 1V ...
Page 4
Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Analog Supply Voltage V A Voltage on Any Pin to GND Input Current at Any Pin (Note 3) Package ...
Page 5
Symbol Parameter V Reference Voltage Range REF DIGITAL INPUT CHARACTERISTICS V Input High Voltage IH V Input Low Voltage IL I Input Current IN C Input Capacitance IND DIGITAL OUTPUT CHARACTERISTICS V Output High Voltage OH V Output Low Voltage ...
Page 6
ADC122S655 Timing Specifications The following specifications apply for V noted. Boldface limits apply for T A Symbol Parameter t CS Setup Time prior to an SCLK rising edge CSSU t D Enable Time after the falling edge ...
Page 7
Timing Diagrams FIGURE 1. ADC122S655 Single Conversion Timing Diagram FIGURE 2. ADC122S655 Continuous Conversion Timing Diagram FIGURE 3. D Rise and Fall Times OUT FIGURE 4. D Hold and Access Times OUT 30051906 FIGURE 5. Valid CS Assertion Times 30051911 ...
Page 8
Specification Definitions APERTURE DELAY is the time between the fourth falling edge of SCLK and the time when the input signal is acquired or held for conversion. COMMON MODE REJECTION RATIO (CMRR measure of how well in-phase signals ...
Page 9
Typical Performance Characteristics 16 MHz 100 kHz unless otherwise stated. IN DNL - 500 kSPS DNL vs DNL vs. V REF V = 5.0V 2.5V REF INL - 500 kSPS 30051921 30051923 ...
Page 10
Typical Performance Characteristics 16 MHz 100 kHz unless otherwise stated. IN DNL vs. SCLK FREQUENCY DNL vs. TEMPERATURE SINAD vs. V www.national.com V = 5.0V REF 30051925 30051929 A 30051933 10 = 2.5V +25°C, ...
Page 11
Typical Performance Characteristics 16 MHz 100 kHz unless otherwise stated. IN SINAD vs. V REF SINAD vs. SCLK FREQUENCY SINAD vs. INPUT FREQUENCY V = 5.0V 2.5V REF 30051937 THD vs. SCLK FREQUENCY 30051941 ...
Page 12
Typical Performance Characteristics 16 MHz 100 kHz unless otherwise stated. IN SINAD vs. TEMPERATURE V CURRENT vs CURRENT vs. TEMPERATURE A www.national.com V = 5.0V 2.5V REF 30051972 V A 30051974 ...
Page 13
Typical Performance Characteristics 16 MHz 100 kHz unless otherwise stated CURRENT vs. TEMP REF SPECTRAL RESPONSE - 500 kSPS V = 5.0V 2.5V REF CMRR vs. CM RIPPLE FREQ 30051951 30051914 13 ...
Page 14
Functional Description The ADC122S655 is a dual 12-bit, simultaneous sampling Analog-to-Digital (A/D) converter. The converter is based on a successive-approximation register (SAR) architecture where the differential nature of the analog inputs is main- tained from the internal track-and-hold circuits throughout ...
Page 15
Single-Ended Input Operation For single-ended operation, the non-inverting inputs of the ADC122S655 can be driven with a signal that has a maximum to minimum value range that is equal to or less than twice the reference voltage. The inverting ...
Page 16
SCLK. In the third condition, CS and SCLK go low simultaneously and the ADC122S655 immediately enters acquisition mode. While there is no timing restriction with respect to the falling edges of CS and ...
Page 17
POWER SUPPLY CONSIDERATIONS AND PCB LAYOUT For best performance, care should be taken with the physical layout of the printed circuit board. This is especially true with a low reference voltage or when the conversion rate is high. At ...
Page 18
FIGURE 12. Interfacing the ADC122S655 to a Current Transducer 6.3 Bridge Sensor Application Figure 13 shows an example of interfacing the ADC122S655 ...
Page 19
Physical Dimensions inches (millimeters) unless otherwise noted 10-Lead MSOP Order Number ADC122S655CIMM NS Package Number MUB10A 19 www.national.com ...
Page 20
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...