adc12c105eb National Semiconductor Corporation, adc12c105eb Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
adc12c105eb
Manufacturer Part Number
adc12c105eb
Description
12-bit, 95/105 Msps A/d Converter
Manufacturer
National Semiconductor Corporation
Datasheet
1.ADC12C105EB.pdf
(24 pages)
www.national.com
Functional Description
Operating on a single +3.3V supply, the ADC12C105 uses a
pipeline architecture and has error correction circuitry to help
ensure maximum performance. The differential analog input
signal is digitized to 12 bits. The user has the choice of using
an internal 1.2V stable reference, or using an external 1.2V
reference. Any external reference is buffered on-chip to ease
the task of driving that pin.
The output word rate is the same as the clock frequency. The
analog input is acquired at the rising edge of the clock and the
digital data for a given sample is delayed by the pipeline for
7 clock cycles. The digital outputs are CMOS compatible sig-
nals that are clocked by a synchronous data ready output
signal (DRDY, pin 21) at the same rate as the clock input. Duty
cycle stabilization and output data format are selectable using
the quad state function OF/DCS pin (pin 12). The output data
can be set for offset binary or two's complement.
Power-down is selectable using the PD pin (pin 30). A logic
high on the PD pin reduces the converter power consumption.
For normal operation, the PD pin should be connected to the
analog ground (AGND).
Applications Information
1.0 OPERATING CONDITIONS
We recommend that the following conditions be observed for
operation of the ADC12C105:
20 MHz
2.0 ANALOG INPUTS
2.1 Signal Inputs
2.1.1 Differential Analog Input Pins
The ADC12C105 has one pair of analog signal input pins,
V
signal, V
Figure 3 shows the expected input signal range. Note that the
common mode input voltage, V
V
mode level for the analog input signal. The positive peaks of
the individual input signals should each never exceed 2.6V.
Each analog input pin of the differential pair should have a
IN
CMO
2.7V
1.2V internal reference
V
V
+ and V
REF
CM
2.4V
(pin 32) for V
= 1.5V (from V
≤
= 1.2V (for an external reference)
≤
IN
V
≤
, is defined as
f
IN
A
CLK
V
−, which form a differential input pair. The input
≤
DR
≤
3.6V
≤
105 MHz
V
CM
V
A
CMO
IN
will ensure the proper input common
= (V
)
IN
+) – (V
CM
, should be 1.5V. Using
IN
−)
18
maximum peak-to-peak voltage of 1V, be 180° out of phase
with each other and be centered around V
peak voltage swing at each analog input pin should not ex-
ceed the 1V or the output data will be clipped.
For single frequency sine waves the full scale error in LSB
can be described as approximately
Where dev is the angular difference in degrees between the
two signals having a 180° relative phase relationship to each
other (see Figure 4). For single frequency inputs, angular er-
rors result in a reduction of the effective full scale input. For
complex waveforms, however, angular errors will result in
distortion.
FIGURE 4. Angular Errors Between the Two Input Signals
It is recommended to drive the analog inputs with a source
impedance less than 100Ω. Matching the source impedance
for the differential inputs will improve even ordered harmonic
performance (particularly second harmonic).
Table 1 indicates the input to output relationship of the AD-
C12C105.
Will Reduce the Output Level or Cause Distortion
FIGURE 3. Expected Input Signal Range
E
FS
= 4096 ( 1 - sin (90° + dev))
30023116
30023115
CM
.The peak-to-