tda8552t NXP Semiconductors, tda8552t Datasheet
tda8552t
Available stocks
Related parts for tda8552t
tda8552t Summary of contents
Page 1
... DATA SHEET TDA8552T; TDA8552TS 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing Product specification Supersedes data of 1998 Jun 02 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 2002 Jan 04 ...
Page 2
... SSOP20 plastic shrink small outline package; 20 leads; body width 4.4 mm 2002 Jan 04 GENERAL DESCRIPTION The TDA8552T is a two channel audio power amplifier that provides an output power of 2 using power supply. The circuit contains two BTL power amplifiers, two digital volume controls and standby/mute logic ...
Page 3
... mode 3 THD = 10 low gain; maximum volume low gain; minimum volume high gain; maximum volume high gain; minimum volume Product specification TDA8552T; TDA8552TS MIN. TYP. MAX. 2 ...
Page 4
... DD 0.5V DD TDA8552T 3 1.6 k down 0. 0. GAIN SELECTION 14 GAINSEL Fig.1 Block diagram. 4 Product specification TDA8552T; TDA8552TS V DD2 V DD3 V DD4 OUT1 MASTER OUT1 SLAVE 2 OUT2 MASTER OUT2 ...
Page 5
... On the PCB the ground pins can be connected to a copper area to decrease the thermal resistance. 2002 Jan 04 DESCRIPTION handbook, halfpage 5 Product specification TDA8552T; TDA8552TS GND1 20 GND4 1 19 OUT2 2 OUT1 ...
Page 6
... Philips Semiconductors 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing FUNCTIONAL DESCRIPTION The TDA8552T 1.4 W BTL audio power amplifier capable of delivering 2 1.4 W output power into an 8 load at THD = 10% using power supply. The gain of the amplifier can be set by the digital volume control. ...
Page 7
... The common ground pin of the headphone is connected to the ground of the amplifier, see Fig.4. By using the HPS pin as illustrated in Fig.4, the TDA8552T detects if a headphone jack plug is inserted into the connector. 2002 Jan 04 When no headphone is plugged in, the voltage level at the HPS pin will remain LOW ...
Page 8
... AC and DC short-circuit safe voltage sc P maximum power dissipation tot THERMAL CHARACTERISTICS See Section “Thermal design considerations” in Chapter “Test and application information”. SYMBOL R thermal resistance from junction to ambient th(j-a) for the TDA8552T (SO20) for the TDA8552TS (SSOP20) Table 1 Power rating; note ...
Page 9
... SE mode 3 MODE DD note 2 GAINSEL = 0 V GAINSEL = V DD standby mute operating 0 < V < V MODE DD note 3 low gain (20 dB) high gain (30 dB) SE mode; headphone detected 9 Product specification TDA8552T; TDA8552TS MIN. TYP. MAX. 2 2.5 50 150 V 0 ...
Page 10
... DC output offset voltage to 2 --------------------------------------------------------------- - The DC output voltage with respect to ground is approximately 0.5V 3. Output voltage in mute position is measured with an input (RMS bandwidth of 20 kHz, so including noise, gain select pin is LOW (0 V). 2002 Jan 04 TDA8552T; TDA8552TS CONDITIONS MIN. 50 100 4.1 1 < V < V ...
Page 11
... THD = 10 THD = 0.5 THD = 0.5 THD = 0.5 0.1 W; note 1 o note 2 note 3 tbf THD = 1 note 4 HPS DD 11 Product specification TDA8552T; TDA8552TS TYP. MAX. UNIT 0.9 W 0.6 W 0.3 W 0.6 W 0.4 W 0 the input. ...
Page 12
... L THD = 0.5 0.1 W; note 0.5 W; note 1 o GAINSEL note 2 GAINSEL note 2 DD note 3 50 THD = 1 note 4 70 HPS Product specification TDA8552T; TDA8552TS TYP. MAX. UNIT 1.4 W 0.8 W 1.0 W 0.6 W 0.15 0.4 % 0.1 0 100 V 100 1. the input ...
Page 13
... note 1 note 2 THD = 1 rep t w increasing volume floating decreasing volume Fig.3 Timing UP/DOWN pin. 13 Product specification TDA8552T; TDA8552TS MIN. TYP. MAX 0.04 60 100 the input. source t rep t w MGM611 ...
Page 14
... DD INTERFACE 15 k 0. STANDBY/MUTE GAIN 4 AND OPERATING SELECTION V DD Fig.4 Test and application diagram. 14 Product specification TDA8552T; TDA8552TS 100 V DD1 DD3 13 OUT1 MASTER 220 OUT1 SLAVE TDA8552T ...
Page 15
... When for the balance control only a single contact is used, the balance steps are 1.25 dB. If double contacts are used for the balance buttons and the dashed connection is made, then the balance steps are 2.5 dB. 15 TDA8552T; TDA8552TS = not specially mentioned dB, audio band-pass L v Product specifi ...
Page 16
... This maximum gain setting is maintained until the supply voltage drops below the minimum value. balance left handbook, full pagewidth balance right 2002 Jan 04 2 100 nF volume 2.2 k 100 nF down Fig.5 Volume and balance control using buttons. 16 TDA8552T; TDA8552TS UP/DOWN1 6 TDA8552T UP/DOWN2 7 MGM612 Product specification ...
Page 17
... DD ( MGR007 handbook, halfpage THD (%) ( (1) G (2) G ( Product specification TDA8552T; TDA8552TS ( volume steps = (max.). (max.). v Fig.7 Gain as a function of volume steps ...
Page 18
... Hz MGR011 handbook, halfpage THD (%) (Hz (1) G ( Product specification TDA8552T; TDA8552TS 10 (1) 1 (2) ( (max.). L v Fig.11 THD as a function (1) (2) ...
Page 19
... ( ( Fig.17 Channel separation as a function of 19 Product specification TDA8552T; TDA8552TS (1) ( (dB kHz; THD = 1 (max.). = 30 dB (max.). (1) ( ...
Page 20
... Jan 04 GND 220 F 100 nF MODE 330 150 nF 330 nF 220 F TDA8552/53TS TDA OUT1 OUT2 Fig.18 Printed-circuit board layout. 20 Product specification TDA8552T; TDA8552TS 77 bottom view Vdd 1 820 k 100 k 1.5 k DOWN 220 220 MGR015 79 ...
Page 21
... scale (1) ( 0.49 0.32 13.0 7.6 10.65 1.27 0.36 0.23 12.6 7.4 10.00 0.019 0.013 0.51 0.30 0.419 0.050 0.014 0.009 0.49 0.29 0.394 REFERENCES JEDEC EIAJ MS-013 21 TDA8552T; TDA8552TS detail 1.1 1.1 1.4 0.25 0.25 0.4 1.0 0.043 0.043 0.055 0.01 0.01 0.016 0.039 EUROPEAN PROJECTION Product specification ...
Page 22
... IEC SOT266-1 2002 Jan 2.5 scale (1) ( 0.32 0.20 6.6 4.5 6.6 0.65 0.20 0.13 6.4 4.3 6.2 REFERENCES JEDEC EIAJ MO-152 22 TDA8552T; TDA8552TS detail 0.75 0.65 1.0 0.2 0.13 0.45 0.45 EUROPEAN PROJECTION Product specification SOT266 ...
Page 23
... If wave soldering is used the following conditions must be observed for optimal results: 2002 Jan 04 TDA8552T; TDA8552TS Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. For packages with leads on two sides and a pitch (e): – ...
Page 24
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2002 Jan 04 TDA8552T; TDA8552TS SOLDERING METHOD WAVE not suitable ...
Page 25
... Product specification TDA8552T; TDA8552TS DEFINITIONS These products are not Philips Semiconductors ...
Page 26
... Philips Semiconductors 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing 2002 Jan 04 TDA8552T; TDA8552TS NOTES 26 Product specification ...
Page 27
... Philips Semiconductors 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing 2002 Jan 04 TDA8552T; TDA8552TS NOTES 27 Product specification ...
Page 28
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2002 All rights are reserved. Reproduction in whole or in part is prohibited ...