tda5153x NXP Semiconductors, tda5153x Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
tda5153x
Manufacturer Part Number
tda5153x
Description
Pre-amplifier Hard Disk Drive With Mr-read/inductive Write Heads
Manufacturer
NXP Semiconductors
Datasheet
1.TDA5153X.pdf
(28 pages)
Philips Semiconductors
8.10.5.3
d2 = logic 1, d1 = don’t care, d0 = either logic or 1. Unlike
the above tests, the thermal asperity detection does not
use the RDx to RDy outputs. Thus, the reader is fully
operational. In case a thermal asperity is detected, it is
flagged at the HUS pin.
The threshold voltage for the thermal asperity detection is
2-bit programmable. These 2 bits consist of d0 (LSB) of
the test mode register (address = 0XXX0110), as the
MSB, and b2 of the compensation register
(address = 0XXX0111).
where d0 is d0 of test mode register and b2 is d2 of
capacitor compensation register.
8.10.6
By default (d2 = d1 = d0 = logic 0) the programmable
capacitors are zero. These capacitors are used to improve
the performance of the write amplifier according to the
write amplifier output load.
8.10.7
By default (d3 = d2 = d1 = d0 = logic 0), the high
frequency gain attenuator is not active. The gain
8.10.10 A
1997 Jul 02
V
0
0
0
A7 A6 A5 A4 A3 A2 A1 A0
th
Pre-amplifier for Hard Disk Drive (HDD)
with MR-read/inductive write heads
=
0
0
0
210
W
H
REGISTER
0
0
1
DDRESS REGISTERS
IGH FREQUENCY GAIN ATTENUATOR POLE
Thermal asperity detector
RITE AMPLIFIER PROGRAMMABLE CAPACITORS
+
560 d0
0
1
0
0
0
0
+
0
0
0
280 b2
; note 1
1
1
1
0
0
0
V
,
configuration register:
power control register:
head select register:
d0 = 0: use data flip-flop; d0 = 1: by-pass data flip-flop
d1 = 0: the WDI inputs are PECL levels; d1 = 1: invalid
d2 = 0: write current inhibit active; d2 = 1: write current inhibit inactive
read mode: d3 = 0: HUS active; d3 = 1: HUS HIGH
write mode: d3 = 0: HUS active; d3 = 1: HUS LOW
d4 = 0: read gain nominal; d4 = 1: read gain nominal + 3 dB
d5 = 0: read amplifier OFF during write mode; d5 = 1: read amplifier ON
during write mode
(d1, d0) = (0, 0): sleep mode
(d1, d0) = (1, 0) or (0, 1): standby mode
(d1, d0) = (1, 1): active mode (write or read)
6 channels: (d2,d1,d0) = (0,0,0) to (1,0,1): H0 to H5
4 channels: (d2,d1,d0) = (0, 0, 1) to (1, 0, 0): H1 to H4
14
attenuator provides a pole which limits the bandwidth and
reduces the high-frequency noise. The HF pole can be
used in combination with the HF zero in order to boost the
HF gain locally and yet limit the very high frequency noise
enhancement.
8.10.8
By default (d3 = d2 = d1 = d0 = logic 0), the high
frequency gain boost is not active. The gain boost provides
a zero which allows to optimize the bandwidth of the read
amplifier and to correct for attenuation caused by series
inductances in the leads between the MR-heads and the
read amplifier inputs.
8.10.9
By default (d2 = d1 = d0 = logic 0) the settle pulse has a
nominal duration of 3 s. Its value can be programmed
from 2.125 s to 3 s according to the following formula:
t
st
=
2
+
H
S
DESCRIPTION
------------------------------------------------------------------------- -
ETTLE PULSE
IGH FREQUENCY GAIN BOOST REGISTER
4 d2
+
2 d1
1
+
1 d0
Preliminary specification
+
1
s
TDA5153