sc14wsmdata Dialog Semiconductor, sc14wsmdata Datasheet - Page 25

• Manufacturer Part Number: sc14wsmdata
• Description: Ultra Low Energy Wireless Sensor Module V1.0
• Manufacturer: Dialog Semiconductor

© 2011 Dialog Semiconductor B.V/
7.0 Notices to OEM
7.1
PRODUCT AND THE END USER.
Product marking
The end product containing the module must be
marked as follows:
"Contains Transmitter Module FCC ID: Y82-SC14A /
IC: 9576A-SC14A"
FCC compliance statement
The manual provided to the end user must include the
following statements:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Module transmetteur ID IC: 9576A-SC14A
Son fonctionnement est soumis aux deux conditions
Suivantes:
1. cet appareil ne doit pas causer D'interférences
nuisibles et
2. cet appareil doit accepter Toute interference recue,
y compris les interferences qui peuvent pertuber le
fontionnement.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit
• Consult the dealer or an experienced radio/TV
7.2
The module is intended to be used in an end
application. When the requirements in 15.2 are fulfilled,
no further test concerning the module is needed. Type
approval concerning the end product, except for the
receiver.
different from that to which the receiver is
connected.
technician for help.
FCC REQUIREMENTS REGARDING THE END
END APPLICATION APPROVAL
Company Confidential
25
module, is the responsibility of the end product
manufacturer.
7.3
This section provides of an overview of the safety
requirements you must adhere to when working with
SC14WSMDATA.
• The specific external power supply for
• Interconnection circuits shall be selected to provide
• Interface type not subjected to over voltages (i.e.
• Requirements additional to those specified in this
• Equipment intended for operation in special
• Equipment intended to be used in vehicles, on board
• Equipment intended for use where ingress of water
• Installation by qualified personnel only!
• The product is a component intended for installation
7.4
Payment of the Up Front Membership Fee and Per
Radiating Device Fees is not required from a
manufacturer or distributor that uses an FCC-certified
module for which such fees have been paid. Such an
“FCC certified module” is defined as a device that
contains the complete UPCS-compliant radio modem
functionality from a supplier that has a valid UTAM
Affidavit. The hardware and firmware implementation
of the FCC certified module must not be modified by
the manufacturer or distributor in a way that would
invalidate its original FCC certification unless the
manufacturer of the device that will contain the module
secures its own FCC approval. Any applicant for FCC
approval seeking to use an FCC certified module must
give the FCC ID number of the certified module that it
will employ and attest that it is using a module for
which UTAM fees have been paid.
Refer to www.utam.org for more information
SC14WSMDATA has to fulfill the requirements
according to clause 2.5 (Limited power source) of
this standard EN 60950-1:2006.
continued conformance to the requirements of
clause 2.2 for SELV (Safety Extra Low Voltage)
circuits according to EN 60950-1:2006 after making
connections.
does not leave the building).
standard may be necessary for:
environments (for example, extremes of
temperature, excessive dust, moisture or vibration,
flammable gases and corrosive or explosive
atmospheres).
ships or aircraft, in tropical countries or at altitudes
greater than 2000 m.
is possible.
and use in complete equipment. The final
acceptance of the component is dependent upon its
installation and use in complete equipment.
SAFETY REQUIREMENTS
UTAM MEMBERSHIP WAIVER
Preliminary December 4, 2012 v1.0