at49lw040 ATMEL Corporation, at49lw040 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
at49lw040
Manufacturer Part Number
at49lw040
Description
At49lw040 4-megabit Firmware Hub Flash Memory
Manufacturer
ATMEL Corporation
Datasheet
1.AT49LW040.pdf
(29 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
at49lw040-33JC
Manufacturer:
ATMEL
Quantity:
1 831
Part Number:
at49lw040-33JC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at49lw040-33TC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Response to Invalid
Fields
Bus Abort
10
AT49LW040
OUTPUT DISABLE: When the FWH is not selected through a FWH read or write cycle,
the FWH interface outputs (FWH[3:0]) are disabled and will be placed in a high-imped-
ance state.
During FWH operations, the FWH will not explicitly indicate that it has received invalid
field sequences. The response to specific invalid fields or sequences is as follows:
•
•
The Bus Abort operation can be used to immediately abort the current bus operation. A
Bus Abort occurs when FWH4 is driven Low, V
will tri-state the Input/Output Communication pins, FWH3 - FWH0 and the FWH state
machine will reset. During a write cycle, there is the possibility that an internal Flash
write or erase operation is in progress (or has just been initiated). If the FWH4 is
asserted during this time frame, the internal operation will not abort. The internal FWH
state machine will not initiate a Flash write or erase operation until it has received the
last nibble from the chipset. This means that FWH4 can be asserted as late as cycle
12 (Table 6) and no internal Flash operation will be attempted.
HARDWARE WRITE-PROTECT PINS TBL AND WP: Two pins are available with the
FWH to provide hardware write-protect capabilities.
The Top Sector Lock (TBL) pin is a signal, when held low (active), prevents program or
sector erase operations in the top sector of the device (sector 7) where critical code can
be stored. When TBL is high, hardware write protection of the top sector is disabled. The
write-protect (WP) pin serves the same function for all the remaining sectors except the
top sector. WP operates independently from TBL and does not affect the lock status of
the top sector.
The TBL and WP pins must be set to the desired protection state prior to starting a pro-
gram or erase operation since they are sampled at the beginning of the operation.
Changing the state of TBL or WP during a program or erase operation may cause
unpredictable results.
Address out of range: The FWH address sequences is seven fields long (28 bits),
but only the last five address fields (20 bits) will be decoded. The most significant bit
(FWH3) in the third address field also will be ignored. The FWH will respond to
these lower addresses, regardless of the value of the more-significant address bits.
Address A22 has the special function of directing reads and writes to the Flash core
(A22 = 1) or to the register space (A22 = 0).
Invalid MSIZE field: If the FWH receives an invalid size field during a read or write
operation, the internal state machine will reset and no operation will be attempted.
The FWH will generate no response of any kind in this situation. Invalid-size fields
for a read cycle are anything but 0000. Invalid-size fields for a write cycle are
anything but 0000. When accessing register space, invalid field sizes are anything
but 0000.
Once valid START, IDSEL, and MSIZE fields are received, the FWH always will
respond to subsequent inputs as if they were valid. As long as the states of FWH
[3:0] and FWH4 are known, the response of the FWH to signals received during the
FWH cycle should be predictable. The FWH will make no attempt to check the valid-
ity of incoming Flash operation commands.
IL
, during the bus operation; the memory
3342A–FLASH–6/03