tza3012hw NXP Semiconductors, tza3012hw Datasheet - Page 13

• Manufacturer Part Number: tza3012hw
• Description: Tza3012hw 30 Mbits/s Up To 3.2 Gbits/s A-rate Fiber-optic Receiver
• Manufacturer: NXP Semiconductors

Philips Semiconductors
Table 11:
V
voltages are referenced to ground; positive currents flow into the device; unless otherwise specified.
[1]
[2]
Table 12:
V
voltages are referenced to ground; positive currents flow into the device; unless otherwise specified.
[1]
[2]
TZA3012HW_1
Product data sheet
Symbol Parameter
V
t
t
f
Timing
t
t
Symbol Parameter
t
r
f
bit(par)
d
sk(o)
jit(tol)(p-p)
CC
CC
clk
o(p-p)
= 3.14 V to 3.47 V; T
The output swing is adjustable in 16 steps controlled by bits MFS in I
only swing = 12 (default) should be used.
With 50 % duty cycle.
= 3.14 V to 3.47 V; T
The peak-to-peak jitter tolerance is expressed as a ratio of the Unit Interval (UI):
The minimum value of the peak-to-peak jitter tolerance is 0.25 for T
t
jit tol p
peak-to-peak output voltage
rise time
fall time
parallel bit rate
delay time
clock duty cycle
output skew time
peak-to-peak jitter tolerance
Parallel outputs characteristics
Jitter tolerance characteristics
data D00 to D15 to clock POCLK
data D06 to D09 to clock POCLK
data D00 to data Dn
data D06 to D09 to clock POCLK
–
p
=
UI max
--------------------------------------------------
amb
amb
UI nom
= 40 C to 85 C; R
= 40 C to 85 C; R
–
UI min
…continued
Conditions
ITU-T G.958; PRBS = (2
STM1/OC3 mode
STM4/OC12 mode
STM16/OC48 mode
Conditions
LVPECL floating; single-ended
with 50
AC-coupled or DC-coupled
20 % to 80 %
80 % to 20 %
referenced to negative clock
edge
POCLK and POCLKQ;
between differential crossovers
between channels
Rev. 01 — 15 December 2005
f = 6.5 kHz
f = 65 kHz
f = 1 MHz
f = 25 kHz
f = 250 kHz
f = 5 MHz
f = 100 kHz
f = 1 MHz
f = 20 MHz
DMX = 1 : 16, 1 : 10, 1 : 8
DMX = 1 : 4
DMX = 1 : 16, 1 : 10, 1 : 8
DMX = 1 : 4
th(j-a)
th(j-a)
external load to V
16 K/W; all characteristics are specified for the default settings; all
16 K/W; all characteristics are specified for the default settings; all
30 Mbit/s up to 3.2 Gbit/s A-Rate fiber-optic receiver
amb
2
C-bus register IOCNF3 (address C8h). In standard LVPECL mode
= 40 C to 0 C at f = 65 kHz and 1 MHz.
31
CC
1)
;
[1]
[2]
[2]
[1]
[2]
[3]
[4]
Min
700
300
300
-
150
40
-
-
Min
3
0.3
0.3
3
0.3
0.3
3
0.3
0.3
100
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Typ
10
1.0
0.5
10
1.0
0.5
10
1.0
0.5
TZA3012HW
Typ
900
350
350
-
180
50
-
-
100
Max
-
-
-
-
-
-
-
-
-
Max
1150
400
400
400
250
60
200
50
250
Unit
13 of 18
Unit
mV
ps
ps
Mbit/s
ps
ps
%
ps
ps