tza3044 NXP Semiconductors, tza3044 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
tza3044
Manufacturer Part Number
tza3044
Description
Sdh/sonet Stm4/oc12 And 1.25 Gbits/s Gigabit Ethernet Postamplifiers
Manufacturer
NXP Semiconductors
Datasheet
1.TZA3044.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
tza3044T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
The relationship between the threshold current and the
detected input voltage is approximately:
In the formulas (1) and (3), the voltage on
pins DIN and DINQ is measured as peak-to-peak value.
Since the voltage on pin RSET is held constant at 1.5 V
below V
Combining these two formulas results in a general formula
to calculate R
Example: Detection should occur if the differential voltage
of the input signals drops below 4 mV (p-p). In this case, a
reference current of 0.0018
into pin RSET. This can be set using a current source or
simply by connecting a resistor of the appropriate value.
The resistor must be connected between V
pin RSET. In this example the value would be:
The hysteresis is fixed internally at 3 dB electrical. In the
example of above, a differential level below 4 mV (p-p) of
the input signal will drive pin ST to LOW, and an input
signal level above 5.7 mV (p-p) will drive pin ST to HIGH.
A function is provided to automatically disable the signal
transmission when the chip senses that the input signal is
below the programmed threshold level. This function can
be put into operation by connecting pin JAM with pin STQ.
When the input signal is below the programmed threshold
level, the data outputs are then forced to a predetermined
state (pin DOUT = LOW and pin DOUTQ = HIGH).
Response time of the input signal level detection circuit is
determined by the time constant of the input capacitors,
together with the filter time constant (1 s internal plus the
additional capacitor at pin CF). For SDH/SONET
applications couple capacitors of 1.5 nF are
recommended, leading to a high-pass frequency of
1999 Nov 03
I
R
R
I
RSET
RSET
ADJ
ADJ
SDH/SONET STM4/OC12 and
1.25 Gbits/s Gigabit Ethernet postamplifiers
=
=
=
=
CCA
------------------------------------- -
-------------- -
0.004
------------ - A
R
V
0.0018
830
1.5
ADJ
DIN
, the current flowing into this pin will be:
ADJ
830
–
=
V
207.5 k
for a given input signal level detection:
DINQ
V
DIN
–
V
DINQ
0.004 = 7.2 A should flow
A
CCA
and
(1)
(2)
(3)
6
the maximum operating temperature.
For the TZA3044TT (TSSOP package), the worst case die
temperature T
than the maximum operating temperature, and therefore
strongly discouraged. It is recommended to lower the
thermal resistance from junction to ambient, e.g. by means
of a dedicated board layout.
However, if the ambient temperature is limited to 75 C or
the power supply is limited to 3.3 0.3 V, the junction
temperature will stay below the maximum value without
further precautions.
Output circuits
The output circuit of ST and STQ is given in Fig.7.
The output circuit of DOUT and DOUTQ is given in Fig.8.
Some PECL termination schemes are given in Fig.9.
approximately 30 kHz and a maximum assert time of
30 s.
Dissipation
Since the thermal resistance from junction to ambient
R
resistance of the SO package (see Chapter “Thermal
characteristics”), the dissipation should be considered
when using the TZA3044TT version.
The formula to calculate the worst case die temperature is:
where
For the TZA3044T (SO package), the worst case die
temperature T
T
th(j-a)
j
T
T
R
P
=
j
amb
max
th(j-a)
= junction temperature
T
of the TSSOP package is higher than the thermal
amb
= ambient temperature
= maximum power dissipation.
= thermal resistance from junction to ambient
+
R
j
j
th j a
= 85 + 115
= 85 + 150
–
TZA3044; TZA3044B
P
max
0.3 = 119.5 C which is below
0.3 = 130 C which is higher
Product specification
(4)