hip6028 Intersil Corporation, hip6028 Datasheet - Page 6

• Manufacturer Part Number: hip6028
• Description: Advanced Pwm And Dual Linear Power Control With Integrated Acpi Support Interface
• Manufacturer: Intersil Corporation

Functional Pin Description
VSEN1 (Pin 19)
This pin is connected to the PWM converter’s output voltage.
The PGOOD and OVP comparator circuits use this signal to
report output voltage status and for over voltage protection.
OCSET (Pin 20)
Connect a resistor (R
upper MOSFET. R
set the PWM converter over-current (OC) trip point
according to the following equation:
An over-current trip cycles the soft-start function. Sustaining
an over-current for 2 soft-start intervals shuts down the
controller.
SS (Pin 9)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 11 A (typically) current source, sets
the soft-start interval of the PWM converter and GTL
controller.
VID0, VID1, VID2, VID3, VID4 (Pins 6, 5, 4, 3 and 2)
VID0-4 are the input pins to the 5-bit DAC. The states of
these five pins program the internal voltage reference
(DACOUT). The level of DACOUT sets the core converter
output voltage. It also sets the core PGOOD and OVP
thresholds.
COMP and FB (Pins 17 and 18)
COMP and FB are the available external pins of the PWM
error amplifier. The FB pin is the inverting input of the error
amplifier and the COMP pin is the error amplifier output.
These pins are used to compensate the voltage-control
feedback loop of the PWM converter.
GND (Pin 14)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
PGOOD (Pin 7)
PGOOD is an open collector output used to indicate the
status of the output voltages. This pin is pulled low when the
core output is not within 10% of the DACOUT reference
voltage and the other outputs are below their under-voltage
thresholds.
The PGOOD output is open for “11111” VID code
combination.
PHASE (Pin 23)
Connect the PHASE pin to the PWM converter’s upper
MOSFET source. This pin is used to monitor the voltage
drop across the upper MOSFET for over-current protection.
(I
I
PEAK
OCSET
=
), and the upper MOSFET on-resistance (r
I
--------------------------------------------------- -
OCSET
r
DS ON
OCSET
R
OCSET
OCSET
, an internal 200 A current source
2-316
) from this pin to the drain of the
DS(ON)
)
HIP6028
UGATE (Pin 24)
Connect UGATE pin to the PWM converter’s upper MOSFET
gate. This pin provides the gate drive for the upper MOSFET.
PGND (Pin 21)
This is the power ground connection. Tie the PWM
converter’s lower MOSFET source to this pin.
LGATE (Pin 22)
Connect LGATE to the PWM converter’s lower MOSFET
gate. This pin provides the gate drive for the lower MOSFET.
VCC (Pin 1)
Provide a 12V bias supply for the IC to this pin. This pin also
provides the gate bias charge for all the MOSFETs
controlled by the IC.
RT (Pin 10)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R
200kHz switching frequency is increased according to the
following equation:
Conversely, connecting a pull-up resistor (R
to VCC reduces the switching frequency according to the
following equation:
FAULT (Pin 8)
This pin is low during normal operation, but it is pulled to
VCC in the event of an over-voltage or over-current
condition.
DRIVE3 (Pin 15)
Connect this pin to the gate of an external N-MOSFET or the
base of an external NPN bipolar transistor. This pin provides
the drive for the linear controller’s pass transistor.
VSEN3 (Pin 16)
Connect this pin to the linear controller’s pass MOSFET
source. The voltage at this pin is regulated to 1.5V.
VOUT2 (Pin 13)
Output of the linear regulator. The voltage at this pin is
regulated to 2.5V for output currents up to 230mA (typically).
SD1&3 (Pin 11)
A TTL-compatible, high level signal applied to this pin
disables the PWM (V
outputs. Leaving this pin unconnected or connecting it to
ground enables these two outputs.
Fs 200kHz
Fs 200kHz
+
–
-------------------- -
R
-------------------- -
R
4 10
5 10
T
T
k
k
7
6
OUT1
T
) from this pin to GND, the nominal
(R
(R
) and linear controller (V
T
T
to 12V)
to GND)
T
) from this pin
OUT3
)