lpc11u12 NXP Semiconductors, lpc11u12 Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
lpc11u12
Manufacturer Part Number
lpc11u12
Description
32-bit Arm Cortex-m0 Microcontroller; Up To 32 Kb Flash; 6 Kb Sram; Usb Device; Usart
Manufacturer
NXP Semiconductors
Datasheet
1.LPC11U12.pdf
(69 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lpc11u12F/201 HN33 0A
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
lpc11u12FBD48/201
Manufacturer:
NXP
Quantity:
1 000
Company:
Part Number:
lpc11u12FBD48/201,
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
lpc11u12FHN33/201
Manufacturer:
NXP
Quantity:
1 000
Part Number:
lpc11u12FHN33/201
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
LPC11U1X
Product data sheet
7.10.1 Features
7.9.1 Features
7.10 SSP serial I/O controller
7.11 I
The USART uses a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
The SSP controllers are capable of operation on a SSP, 4-wire SSI, or Microwire bus. It
can interact with multiple masters and slaves on the bus. Only a single master and a
single slave can communicate on the bus during a given data transfer. The SSP supports
full duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
The LPC11U1x contain one I
The I
(SCL) and a Serial Data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I
controlled by more than one bus master connected to it.
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C-bus serial I/O controller
Maximum USART data bit rate of 3.125 Mbit/s.
16-byte receive and transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
Fractional divider for baud rate control, auto baud capabilities and FIFO control
mechanism that enables software flow control implementation.
Support for RS-485/9-bit mode.
Support for modem control.
Support for synchronous mode.
Includes smart card interface.
Maximum SSP speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
2
C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock line
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 11 January 2012
2
C-bus controller.
32-bit ARM Cortex-M0 microcontroller
2
C is a multi-master bus and can be
LPC11U1x
© NXP B.V. 2012. All rights reserved.
20 of 69