hsp50214b Intersil Corporation, hsp50214b Datasheet - Page 52
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
hsp50214b
Manufacturer Part Number
hsp50214b
Description
Programmable Downconverter
Manufacturer
Intersil Corporation
Datasheet
1.HSP50214B.pdf
(62 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
hsp50214bVCZ
Manufacturer:
AD
Quantity:
1 001
Company:
Part Number:
hsp50214bVIZ
Manufacturer:
HONGFA
Quantity:
30 000
Part Number:
hsp50214bVIZ
Manufacturer:
INTERSIL
Quantity:
20 000
POSITION
POSITION
POSITION
31-17
16-15
13-11
BIT
31-28
27-16
30-28
27-25
24-21
20-18
8-3
2-0
14
10
11-0
BIT
BIT
9
31
CONTROL WORD 17: DISCRIMINATOR FILTER CONTROL, DISCRIMINATOR DELAY (SYNCHRONIZED TO PROCCLK)
Reserved
Phase Multiplier
Discriminator Enable
Discriminator FIR
Decimation
FIR Symmetry Type
FIR Symmetry
Number of FIR Taps
Discriminator Delay
Reserved
NCO Divide
Reference Divide
Reserved
Data Source for
SEROUTA
Data Source for
SEROUTB
Number of Serial Word
Links in a Chain
Link Following I Data
FUNCTION
FUNCTION
FUNCTION
CONTROL WORD 18: TIMING ERROR PRELOADS (SYNCHRONIZED TO PROCCLK)
CONTROL WORD 19: SERIAL OUTPUT ORDER (SYNCHRONIZED TO PROCCLK)
52
Reserved.
These bits program allow the phase output of the cartesian to polar converter to be multiplied by 1, 2, 4, or
8 (modulo 2π) to remove phase modulation before the frequency is measured.
00- No Shift on Phase Input to frequency discriminator.
01- Shift Phase Input to frequency discriminator up 1 (one bit), discarding the MSB and zero filling the LSB.
10- Shift Phase Input to frequency discriminator up 2 (two) bits, discarding the MSB and zero filling the LSB.
11- Shift Phase Input to frequency discriminator up 3 (three) bits, discarding the MSB and zero filling the LSB.
0- Disable Discriminator.
1- Enable Discriminator.
The decimation can be programmed from 1 to 8, where 000 = decimate by 8; 001 = decimate by 1; 010 =
decimate by 2; 011 = decimate by 3; 100 = decimate by 4; 101 = decimate by 5; 110 = decimate by 6; and
111 - decimate by 7.
0- Odd Symmetry.
1- Even Symmetry.
0- Symmetric.
1- Asymmetric.
Number of FIR taps from 1 to 63, where 00000 is not valid (00001 = 1 tap, 00010 = 2 taps, etc. up to 11111
= 63 taps). Bit 8 is the MSB.
Sets the number of delays from 1 to 8 in the discriminator. Set delay ddd to delay minus 1, where 000
represents 1 delay; 001 represents 2 delays, 010 represents 3 delays, 011 represents 4 delays, 100
represents 5 delays, 101 represents 6 delays, 110 represents 7 delays, and 111 represents 8 delays. If ddd
the decimal representation bits 2-0, then the discriminator a transfer function H(Z) = 1-Z
Reserved.
The Re-Sampler NCO output is divided down by the value loaded into this register plus 1. Load with a
value that is one less than the desired period. Bit 27 is the MSB.
The reference clock is divided down by the value loaded into this register plus 1. Load with a value that
is one less than the desired period. Bit 27 is the MSB. A minimum preload of “I” is required.
Reserved.
Serial Output A Source. The serial data source is selected using Table 12 (see Output Section).
Serial Output B Source. The serial data source is selected using Table 12 (see Output Section).
This parameter determines the number of SERSYNC pulses generated. It can be set from 1 to 7. If this
parameter matches the number of serial words that are linked together to form a serial output chain, then
there will be a sync pulse for every word in the serial output. In applications where a processor is
receiving the serial data, it may be desirable to have a single SERSYNC pulse for the whole serial output
chain, instead of a SERSYNC for each word in the data chain. The processor then parses out the various
data words. As an example, if the I and Q are chained together and a single SERSYNC pulse is
generated for this serial output chain, no ambiguity exists in the processor about which two data samples
(one from I and one from Q) are related.
The serial data word, or link, following the I data word is selected using Table 12
(see Output Section).
HSP50214B
DESCRIPTION
DESCRIPTION
DESCRIPTION
-(ddd + 1)
.
May 1, 2007
FN4450.4