uaa3522hl NXP Semiconductors, uaa3522hl Datasheet
uaa3522hl
Available stocks
Related parts for uaa3522hl
uaa3522hl Summary of contents
Page 1
... DATA SHEET UAA3522HL Low power dual-band GSM transceiver with an image rejecting front-end Preliminary specification Supersedes data of 2000 Feb 18 File under Integrated Circuits, IC17 INTEGRATED CIRCUITS 2000 Aug 15 ...
Page 2
... GSM 900 MHz hand-held transceiver GSM/DCS dual-band solution with the UAA2077CM (down to 3 UAA2077TS/D (down to 2.7 V). GENERAL DESCRIPTION The UAA3522HL integrates the receiver and most of the transmitter section of a GSM hand-held transceiver. It also integrates the receiver IF and the transmitter section of a DCS transceiver. ...
Page 3
... IF frequency in all modes IF ORDERING INFORMATION TYPE NUMBER NAME UAA3522HL LQFP48 2000 Aug 15 PARAMETER PACKAGE DESCRIPTION plastic low profile quad flat package; 48 leads; body 7 3 Preliminary specification UAA3522HL MIN. TYP. MAX. UNIT 925 960 MHz 880 915 MHz 1710 1785 MHz 200 ...
Page 4
... MHz 90 PHASE SHIFTER 90 PHASE SHIFTER ADDER 0 SAW 46 PHASE SHIFTER 90 0 PHASE SHIFTER ADDER 0 90 UAA3522HL PROGRAMMABLE DIVIDER RF PHASE/ CHARGE DIVIDER FREQUENCY PUMP 5 DETECTOR ADDER PHASE DETECTOR 90 CHARGE PUMP 44, 45 Fig.1 Block diagram VCO 400 MHz ...
Page 5
... RF receiver input A RXIRFB 42 RF receiver input B GNDRF 43 RF receiver and transmit modulation loop ground TXIFA 44 transmit IF external filter A TXIFB 45 transmit IF external filter B RXOIFA 46 receiver IF output A RXOIFB 47 receiver IF output B GNDIF1 48 IF section of RF receiver ground 1 5 Preliminary specification UAA3522HL DESCRIPTION ...
Page 6
... V CCIF1 REFAGC 6 GNDIF2 7 RXIIFA 8 RXIIFB 9 V CCIF2 10 TXON 11 V CCIFLO 12 2000 Aug 15 UAA3522HL Fig.2 Pin configuration. 6 Preliminary specification UAA3522HL V CCPHD 36 35 PHDOUT 34 GNDPHD 33 RXON 32 GNDRFLO 31 RFLOE 30 RFLOC V CCRFLO 29 28 SYNON 27 GNDCP 26 CPORF V CCCPRF 25 FCA043 ...
Page 7
... The circuit can be powered on in one of four operating modes in which different parts of the device are enabled or disabled. The four operating modes are called Idle, RX, TX and SYN, and are selected by the hardware control voltage level applied to pins RXON, TXON and SYNON. 7 Preliminary specification UAA3522HL ...
Page 8
... IF circuits are used for both GSM and DCS applications to avoid duplication. For DCS applications using the UAA2077XM, for example, the RF section of the UAA3522HL does not have to be powered on. The RF section is enabled or disabled by the status of bit RF when the RX mode is activated (see Table 3). ...
Page 9
Table 4 Register bit allocation X = don’t care; MSB = Most Significant Bit; LSB = Least Significant Bit. FIRST BIT MSB RF LO frequency divider ratio X ...
Page 10
... Preliminary specification UAA3522HL AGC AMPLIFIER BIT 0 (LSB) GAIN (dB ...
Page 11
... CLK = HIGH-level; note 2 , RXOIFA and RXOIFB) CCIF1 RX mode active RX mode active TX mode active 11 Preliminary specification MIN. TYP. 0 CONDITIONS VALUE 65 MIN. TYP. 2.7 2.7 2 and V CCCPRF CCPHD CCRF 40 16.9 10.1 7.4 UAA3522HL MAX. UNIT + +150 C +70 C UNIT K/W MAX. UNIT 3 5.5 V 100 A 21.9 mA 14.1 mA 9.6 mA ...
Page 12
... CCCPRF CCPHD RX mode active; note 3 TX mode active; note 3 SYN mode active; note 3 TX mode active RX mode active 12 Preliminary specification MIN. TYP. 5.5 1 1.4 8.6 9.8 5.6 ) 17.9 11.2 6 RXOIFA and RXOIFB CCRF 44.9 20.3 21.7 1.125 1.25 1.175 1.25 1.9 UAA3522HL MAX. UNIT 6.6 mA 1.5 mA 6.7 mA 1.7 mA 10.9 mA 12.6 mA 7.5 mA 23.6 mA 14.6 mA 7.6 mA 59.6 mA 26.4 mA 27.4 mA 1.325 V 1. ...
Page 13
... R ; notes 1, 3 and 4 i(dif) note amb over temperature range note MHz; i(RF) RF input power = 101 dBm; note 1 13 Preliminary specification UAA3522HL . ‘LOW-level’ means the control CCRFLO(TX) CCRFLO(RX) CCPHD(TX CCRFLO(SYN) MIN. TYP. MAX. 925 960 146 0 ...
Page 14
... dB; note 8 conv(dif)(max note 8 conv(dif)(min dB; notes 6 and 7 conv 200 kHz and 3 mod note 10 DC < f < 67.7 kHz mod 14 Preliminary specification UAA3522HL MIN. TYP. MAX. UNIT 200 MHz 2.5 0.5 +1 ...
Page 15
... MHz 2 o(IF) note 200 MHz 3 o(IF) note 200 MHz o(IF) 67.7 kHz; note 400 kHz offset MHz offset mod(peak) TXIRFA TXIRFB) AND 15 Preliminary specification UAA3522HL MIN. TYP 0.75 60 +60 50 100 67.7 kHz I(IQ) O(IQ) mod 0 2 0.225 0.25 ...
Page 16
... TX mode disabled f = 67.7 kHz; mod f = 880 to 915 MHz; o(RF)(GSM 1710 to 1785 MHz o(RF)(DCS 67.7 kHz; mod f = 880 to 915 MHz; o(RF)(GSM 1710 to 1785 MHz o(RF)(DCS note Preliminary specification UAA3522HL MIN. TYP. 1 14.5 10 5.5 11 1710 1785 100 1 14.5 10 5.5 11 ...
Page 17
... Fig.5 REFIN MHz ref MHz ref ( RXIRFA, RXIRFB MODES PINS AND within the closed-loop bandwidth dBm 1.1 GHz xtal LO(RF) 17 Preliminary specification UAA3522HL MIN. TYP 400 1 1.5 = 400 MHz 125 ...
Page 18
... dBm 400 MHz xtal LO(IF MHz; second order loop offset filter closed-loop bandwidth = 25 kHz sink or source current fixed ratio fixed ratio 90% of the final current 18 Preliminary specification UAA3522HL MIN. TYP. MAX 1.8 2.2 2.6 o(cp 0.4 V 0.4 ...
Page 19
... Oscillator configured as shown in the evaluation board diagram Fig.7. handbook, full pagewidth 50 LOW LOSS BALUN input port 2000 Aug 15 typ. i(LO RXIRFA RXOIFA RF RECEIVER RXOIFB RXIRFB Fig.3 RF receiver test principle. 19 Preliminary specification UAA3522HL BALUN /50 output port FCA047 ...
Page 20
... Aug EXTERNAL IF FILTER 47 nH 330 330 TXIFA TXIFB Fig.4 I/Q modulator output. V CCIFLO UAA3522HL IFLOC IF VCO IFLOE XTAL GNDIFLO FCA048 Fig.5 Evaluating IF LO buffer. 20 Preliminary specification UAA3522HL 2 k FCA045 SOURCE ...
Page 21
... CLK DATA MSB EN t d(ENL-CLKH) 2000 Aug see Fig.6; unless otherwise specified. amb PARAMETER T cy(CLK) ACTIVE Fig.6 Serial bus timing diagram. 21 Preliminary specification UAA3522HL MIN. TYP 100 40 20 150 150 500 d(CLKL-ENH ...
Page 22
... TXON 8 330 BB149 100 pF 100 pF This schematic represents the UAA3522HL characterisation board for GSM application and does not guarantee full specification for any particular application 120 2 3 ...
Page 23
... GSM TX RF VCO 880 to 915 MHz 35 1710 to 1785 MHz POWER DCS BAND AMPLIFIER DCS TX RF VCO 1710 to 1785 MHz Fig.8 Typical application block diagram of a GSM dual-band solution using the UAA2077XM DCS front-end and the UAA3522HL transceiver. 90 PHASE SHIFTER 90 PHASE SHIFTER ADDER 0 ...
Page 24
... 2.5 scale (1) ( 0.27 0.18 7.1 7.1 9.15 0.5 0.17 0.12 6.9 6.9 8.85 REFERENCES JEDEC EIAJ MS-026 24 Preliminary specification detail 9.15 0.75 1.0 0.2 0.12 0.1 8.85 0.45 EUROPEAN PROJECTION UAA3522HL SOT313 (1) ( 0.95 0. 0.55 0.55 0 ISSUE DATE 99-12-27 00-01-19 ...
Page 25
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 25 Preliminary specification UAA3522HL ...
Page 26
... This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. 26 Preliminary specification UAA3522HL SOLDERING METHOD (1) WAVE REFLOW suitable ...
Page 27
... Preliminary specification UAA3522HL These products are not ...
Page 28
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + 101 ...