ADF4110 Analog Devices, ADF4110 Datasheet - Page 10

• Manufacturer Part Number: ADF4110
• Description: Single, Integer-N, 550 MHZ PLL With Programmable Prescaler And Charge Pump
• Manufacturer: Analog Devices

ADF4110/ADF4111/ADF4112/ADF4113
CIRCUIT DESCRIPTION
REFERENCE INPUT SECTION
The reference input stage is shown in Figure 2. SW1 and SW2
are normally-closed switches. SW3 is normally-open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REF
on power-down.
RF INPUT STAGE
The RF input stage is shown in Figure 3. It is followed by a
2-stage limiting amplifier to generate the CML (Current Mode
Logic) clock levels needed for the prescaler.
PRESCALER (P/P+1)
The dual-modulus prescaler (P/P+1), along with the A and B
counters, enables the large division ratio, N, to be realized
(N = BP + A). The dual-modulus prescaler, operating at CML
levels, takes the clock from the RF input stage and divides it
down to a manageable frequency for the CMOS A and B counters.
The prescaler is programmable. It can be set in software to 8/9,
16/17, 32/33, or 64/65. It is based on a synchronous 4/5 core.
A AND B COUNTERS
The A and B CMOS counters combine with the dual modulus
prescaler to allow a wide ranging division ratio in the PLL feed-
back counter. The counters are specified to work when the
prescaler output is 200 MHz or less. Thus, with an RF input
frequency of 2.5 GHz, a prescaler value of 16/17 is valid but a
value of 8/9 is not valid.
RF
RF
REF
IN
IN
IN
A
B
GENERATOR
NC
POWER-DOWN
SW1
BIAS
CONTROL
NO
NC
500
SW3
SW2
100k
1.6V
500
BUFFER
AGND
AV
TO R COUNTER
DD
IN
pin
Pulse Swallow Function
The A and B counters, in conjunction with the dual modulus
prescaler, make it possible to generate output frequencies that
are spaced only by the Reference Frequency divided by R. The
equation for the VCO frequency is as follows:
f
P
B
A
f
R
R COUNTER
The 14-bit R counter allows the input reference frequency to be
divided down to produce the reference clock to the phase fre-
quency detector (PFD). Division ratios from 1 to 16,383 are
allowed.
PHASE FREQUENCY DETECTOR (PFD) AND CHARGE
PUMP
The PFD takes inputs from the R counter and N counter
(N = BP + A) and produces an output proportional to the phase
and frequency difference between them. Figure 5 is a simplified
schematic. The PFD includes a programmable delay element
which controls the width of the antibacklash pulse. This pulse
ensures that there is no dead zone in the PFD transfer function
and minimizes phase noise and reference spurs. Two bits in the
Reference Counter Latch, ABP2 and ABP1 control the width
of the pulse. See Table III.
VCO
REFIN
INPUT STAGE
FROM RF
Output frequency of external voltage controlled oscilla-
tor (VCO).
Preset modulus of dual modulus prescaler
Preset Divide Ratio of binary 13-bit counter (3 to 8191).
Preset Divide Ratio of binary 6-bit swallow counter (0 to
63).
Output frequency of the external reference frequency
oscillator.
Preset divide ratio of binary 14-bit programmable refer-
ence counter (1 to 16383).
f
MODULUS
CONTROL
VCO
N = BP + A
PRESCALER
= [(P × B) + A] × f
P/P + 1
LOAD
LOAD
COUNTER
COUNTER
13-BIT B
6-BIT A
REFIN
/R
TO PFD