SCCC1A150C1B SAMWHA [SAMWHA ELECTRIC], SCCC1A150C1B Datasheet - Page 3

• Manufacturer Part Number: SCCC1A150C1B
• Description: Surface Mount Disc Capacitors
• Manufacturer: SAMWHA [SAMWHA ELECTRIC]

Mechanical test and Environmental Substance
No.
138
1
2
3
4
5
6
Adhesive Strength of
Terminal
Vibration
Resistance
Bending
Strength
Solderability Test
Solder
Heat
Resistance
The regulation of
environmental pollution
materials.
SAMWHA CAPACITOR Co., Ltd.
Item
Appearance
Capacitance
Change
Dissipation
Factor (tan δ , Q)
I.R
Appearance
Capacitance
Change
Appearance
Capacitance
Change
Dielectric
Strength
No. visible damage
±5% or ±0.5 pF
Whichever is larger
from initial measurement
Q ≥ 200
More than 1000MΩ
No. visible damage
±5% or ±0.5 pF
Whichever is larger
from initial measurement
No. visible damage
±5% or ±0.5 pF
Whichever is larger
from initial measurement
No. Failure
※ Never use materials mentioned below in high voltage products regulated this document.
※ Pb, Hg, Cr+6, PBB, PBDE : 100ppm, Cd : 5ppm
※ Exception : - Pb of solder : <1000ppm
No removal of the termination or other
defect should occur.
Visual examination terminals area shall
be at least 90% covered with a new
solder coating
Fig.3
SCC Type
Requirement
B : With ± 10%
E : With ± 20%
F : With ± 30%
B : With ± 10%
E : With ± 20%
F : With ± 30%
B : With ± 5%
E : With ± 15%
F : With ± 20%
B,E : 5% Max.
F : 7.5% Max.
SCK, SCG, SSC,
SSD Type
- Pb of ceramic(dielectric)
Solder the capacitor to the testing jig (glass epoxy
board) shown in Fig. 2 using a eutectic solder. Then
apply 5 N force in the direction of the arrow. The
soldering should be used the reflow method and
should be conducted with care so that the soldering is
uniform and free of defects such as heat shock.
The capacitor should be subjected to a simple
harmonic motion having a total amplitude of 1.5mm,
the frequency being varied uniformly between the
approximate limits of 10 and 55Hz. The frequency
range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should
be applied for a period of 2hrs. in each 3mutually
perpendicular directions (total of 6hrs.)
Solder the capacitor to the testing jig (glass epoxy
board) shown in Fig. 3 using a eutectic solder.
Then apply a force in the direction shown in Fig. 4.
The soldering should be done either with an iron or
using the reflow method and should be conducted
with care so that the soldering is uniform and free of
defects such as heat shock.
Soldering Method : Reflow Soldering
- Maximum Temperature : 250℃ max.
- Preheating Temperature : 150~180℃, 60~180 sec.
Soldering Method : Reflow Soldering
- Maximum Temperature : 250℃ max.
- Preheating Temperature : 150~180℃, 60~180 sec.
- After testing, The capacitors shall be subjected to the
standard test condition for a period 24 hours and shall
be measured.
Fig.2
Fig.4
Test Conditions
(245± 5℃, 5± 0.5 sec.)
(245± 5℃, 5± 0.5 sec.)