kac-9628 ETC-unknow, kac-9628 Datasheet - Page 31

• Manufacturer Part Number: kac-9628
• Description: Kodak Kac-9628 Cmos Image Sensor 648 H X 488 V High Dynamic Range 30 Fps Color Cis
• Manufacturer: ETC-unknow

IMAGE SENSOR SOLUTIONS
Register Set
Register Name Digital Video Mode 2
Address
Mnemonic
Type
Reset Value
Register Name Snapshot Mode Configuration Register
Address
Mnemonic
Type
Reset Value
www.kodak.com/go/imagers 585-722-4385
7:4
3:0
7:6
5
4
3
2
1
0
Bit
Bit
SsFrames
ShutterMode
ExtSynPol
SnapshotMod
SnapShotPol
SnapEnable
Bit Symbol
HsyncAdjust
Bit Symbol
08 Hex
VMODE2
Read/Write
00 Hex
09 Hex
SNAPMODE
Read/Write
00 Hex
(continued)
Use to program the leading edge
of hsync to the first valid pixel at
the beginning of each row. This
can be 0-hex to F-hex corre-
sponding to 0 - 15 pixel clocks.
Default 0.
Reserved
Program to set the number of
frames required before readout
during a snapshot with no external
shutter, (see Figure 26). By
default these two bits are set to
00. Set to any value but 00 for
snapshot to function properly..:
Assert to indicate that an external
shutter will be used during snap-
shot mode. Clear (the default) to
indicate that snapshot mode will
be carried out without the aid of an
external shutter.
Assert to set the active level of the
extsync signal to 0. Clear (the
default) to set the active level of
the extsync signal to 1.
Reserved
Assert to set the snapshot pin to
level mode. In level mode the sen-
sor will continually run snapshot
sequences as long as the snap-
shot pin is held to the active level.
Clear (the default) to set the snap-
shot signal to pulse mode. In
pulse mode the sensor will only
carry out one snapshot sequence
per pulse applied to the snapshot
pin.
Assert to set the snapshot pin to
be active on the positive edge.
Clear (the default) to set the snap-
shot pin to be active on the nega-
tive edge.
Set to enable the external snap-
shot pin. Clear (the default) to dis-
able the external snapshot pin.
00
01
10
11
Reserved
one frame
two frames
three frames
Description
Description
31
Register Name Scan Window Row Start Register
Address
Mnemonic
Type
Reset Value
Register Name Scan Window Row End Register
Address
Mnemonic
Type
Reset Value
Register Name Scan Window Mode B LSB Register
Address
Mnemonic
Type
Reset Value
Register Name Display Window Row Start Register
Address
Mnemonic
Type
Reset Value
Register Name Display Row End Register
Address
Mnemonic
Type
Reset Value
7:0
7:0
7
6:2
1
0
7:0
7:0
Bit
Bit
Bit
Bit
Bit
SwStartRow
[8:1]
SwEndRow
[8:1]
SwMode
SwEndRow
[0]
SwStartRow
[0]
DwStartRow
DwEndRow
Bit Symbol
Bit Symbol
Bit Symbol
Bit Symbol
Bit Symbol
0B Hex
SROWS
Read/Write
00 Hex
0C Hex
SROWE
Read/Write
FB Hex
0DHex
SWLSB
Read/Write
00 Hexx
0E Hex
DROWS
Read/Write
00 Hex
0F Hex
DROWE
Read/Write
FB Hex
Use to program the scan window’s
start row address MSBs. If bit 6 of
register DWLSB is set to 1 the
start row address is incremented
by 1 else the raw value is used.
Use to program the scan window’s
end row address MSBs. If bit 6 of
register DWLSB is set to 1 the end
row address is incremented by 1.
else the raw value is used.
Use to program the scan window’s
addressing mode. Set to a logic
one for mode b and a logic 0 for
mode a.
Reserved
Use to program bit 0 of the scan
window’s end row address.
Use to program bit 0 of the scan
window’s start row address.
Use to program the display win-
dow’s start row address MSBs.
The LSB can be programmed
using the DWLSB register.
Use to program the display win-
dow’s end row address. The LSB
can be programmed using the
DWLSB register.
Email:[e-mail]
Description
Description
Description
Description
Description