kac-9628 ETC-unknow, kac-9628 Datasheet - Page 8

• Manufacturer Part Number: kac-9628
• Description: Kodak Kac-9628 Cmos Image Sensor 648 H X 488 V High Dynamic Range 30 Fps Color Cis
• Manufacturer: ETC-unknow

IMAGE SENSOR SOLUTIONS
Video Amplifier Specifications
The following specifications apply for all VDD pins= +3.3V. Boldface limits apply for TA = T
AC Electrical Characteristics
The following specifications apply for All VDD pins = +3.3V. Boldface limits apply for T
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10: The dew point temperature (the temperature below which there is a possibility of moisture condensation forming inside the
www.kodak.com/go/imagers 585-722-4385
Symbol
V
C
Symbol
gain
FRM
gain
T
T
F
F
rc
T
reset
mclk
T
hclk
, T
ch
cl
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate con-
ditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications
and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions
listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to VSS = vss_ana = vss_od = vss_dig = 0V, unless otherwise specified.
When the voltage at any pin exceeds the power supplies (VIN < VSS or VIN > VDD), the current at that pin should be lim-
ited to 25mA. The 50mA maximum package input current rating limits the number of pins that can safely exceed the power
supplies with an input current of 25mA.
The absolute maximum junction temperature (TJmax) for this device is 125
is dictated by TJmax, the junction-to-ambient thermal resistance (ΘJA), and the ambient temperature (T
culated using the formula PDMAX = (TJmax - T
and 1.94W at the maximum operating ambient temperature of 50
normal operation will be well under the PDMAX of the package.
Human body model is 100pF capacitor discharged through a 1.5kΩ resistor. Machine model is 220pF discharged through
ZERO Ohms.
See AN450, “Surface Mounting Methods and Their Effect on Product Reliability”, or the section entitled “Surface Mount”
found in any post 1986 National Semiconductor Linear Data Book, for other methods of soldering surface mount devices.
The analog inputs are protected as shown below. Input voltage magnitude up to 500mV beyond the supply rails will not
damage this device. However, input errors will be generated If the input goes above AV+ and below AGND.
Typical figures are at TJ = 25
Test limits are guaranteed to AOQL (Average Outgoing Quality Level).
package) of the package is rated at -20
sensor between -40
rate
fc
Video Amplifier Nominal Gain
Color Amplifiers Nominal Gain
Input Clock Frequency
Clock High Time
Clock Low Time
Clock Duty Cycle
Clock Input Rise and Fall Time
Internal System Clock Fre-
quency
Reset pulse width
Frame Rate
Parameter
Parameter
o
C and -20
o
C, and represent most likely parametric norms.
0
C.
o
C. Suitable precautions should be taken to avoid dew formation when operating the
64 linear steps
128 linear steps
@ CLK
@ CLK
@ CLK
Conditions
Pad
A
max
max
max
)/ΘJA. In the 48-pin LCC, ΘJA is 38.5
Conditions
IOP
8
VDD
VSS
o
C. Note that the power dissipation of this device under
Internal Circuits
note 9
45/55
Min
1.0
1.0
12
10
10
1
o
C. The maximum allowable power dissipation
A
= T
note 9
Typical
note 8
Min
MIN
0
MIN
to T
to T
o
C/W, so PDMAX = 2.5W at 25
MAX
Typical
MAX
note 8
0-15
0-14
: all other limits T
note 9
: all other limits T
Email:[e-mail]
55/45
Max
14.0
48
45
45
30
note 9
A
Max
), and can be cal-
min/max
Units
MHz
MHz
ns
ns
µs
fps
ns
A
A
= 25
Units
= 25
dB
dB
o
o
C
C
o
C