STV-5410-R01 STMICROELECTRONICS [STMicroelectronics], STV-5410-R01 Datasheet - Page 5

no-image

STV-5410-R01

Manufacturer Part Number
STV-5410-R01
Description
Mono and Colour Digital Video CMOS Image Sensors
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
CMOS Sensor; Customer Datasheet, Rev 3.0, 28 September 2000
2.
2.1
VV5410/VV6410 is a CIF format CMOS image sensor. The VV5410 sensor is the basic monochrome device and VV6410 is the
colourised variant. The operation of VV5410 and VV6410 is very similar but any differences will be identified and explained.
VV6410 can output digital colourised pixel data at frame and line rates compatible with either NTSC or PAL video standards.
VV5410 and VV6410 contain the same basic video timing modes. Table 2 summarises these video modes.
The various operating modes are detailed in Section 3.
Important: VV5410 and VV6410’s output video data stream only contains raw data. A master co-processor is required to
generate a video waveform that can be displayed on a VDU
Note: The user can also provide a 24 MHz clock, rather than a 16 MHz clock, for the QCIF-60fps, CIF-25fps and CIF-30fps
modes, which the sensor then internally divides by 1.5, (see data_format[22]), to give an effective input clock frequency of 16
MHz.
2.2
VV5410/VV6410 does not include any form of automatic exposure and/or gain control. Thus to produce a correctly exposed
image the integration period for the pixels, in the sensor array, an exposure control algorithm must be implemented externally.
The new exposure values are written to the sensor via the serial interface.
2.3
The sensor’s offers a very flexible digital interface, the main components of which are listed below:
1. A tri-stateable 5-wire data bus (D[4:0]) for sending both video data and embedded timing references.
2. 4-wire and 8-wire data bus alternatives available. If the 8-wire option is selected then the FST/LST pins are reconfigured to
3. A data qualification clock, QCK, which can be programmable via the serial interface to behave in a number of different ways
4. A line start signal, LST (Tri-stateable).
5. A frame start signal, FST (Tri-stateable).
6. OEB tri-states all 5 data bus lines, D[4:0], the qualification clock, QCK, LST, FST and D[7].
7. A 2-wire serial interface (SDA,SCL) for controlling and setting up the device.
NTSC (3.2 fsc)
QCIF - 25 fps
QCIF - 30 fps
QCIF - 60 fps
Introduction
output data information.
(Tri-stateable).
PAL (3.2 fsc)
CIF - 25 fps
CIF - 30 fps
Overview
Exposure Control
Digital Interface
Mode
28.636360 / 2.5
35.46895 / 2.5
Input Clock
(MHz)
16.00
16.00
16.00
8.00
8.00
Note
Commercial in confidence
cd5410-6410f-3-0.fm
System
Divisor
Clock
8
8
8
4
4
2
2
Table 2 : Video Modes
Image Size
180 x 148
180 x 148
180 x 148
356 x 292
356 x 292
306 x 244
356 x 292
Line Time
63.555564
63.999639
250.00
208.00
104.00
125.00
104.00
( s)
Frame
Lines
per
160
160
160
320
320
525
625
VV5410 & VV6410
Frame Rate
25.00000
30.04807
60.09614
25.00000
30.04807
29.97003
25.00014
(fps)
5/105

Related parts for STV-5410-R01