LT1963EST LINEAR [Linear Integrated Systems], LT1963EST Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
LT1963EST
Manufacturer Part Number
LT1963EST
Description
1.5A, Low Noise, Fast Transient Response LDO Regulators
Manufacturer
LINEAR [Linear Integrated Systems]
Datasheet
1.LT1963EST.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1963EST
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1963EST-1.5
Manufacturer:
LINEAR
Quantity:
20 000
Part Number:
LT1963EST-1.5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1963EST-1.8
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LT1963EST-1.8#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1963EST-2.5
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LT1963EST-3.3
Manufacturer:
Linear Technology
Quantity:
1 902
Company:
Part Number:
LT1963EST33
Manufacturer:
LT
Quantity:
6 487
PI FU CTIO S
OUT: Output. The output supplies power to the load. A
minimum output capacitor of 10 F is required to prevent
oscillations. Larger output capacitors will be
required for applications with large transient loads to limit
peak voltage transients. See the Applications Information
section for more information on output capacitance and
reverse output characteristics.
SENSE: Sense. For fixed voltage versions of the LT1963
(LT1963-1.8/LT1963-2.5/LT1963-3.3), the SENSE pin is
the input to the error amplifier. Optimum regulation will be
obtained at the point where the SENSE pin is connected to
the OUT pin of the regulator. In critical applications, small
voltage drops are caused by the resistance (R
between the regulator and the load. These may be elimi-
nated by connecting the SENSE pin to the output at the
load as shown in Figure 1 (Kelvin Sense Connection). Note
that the voltage drop across the external PC traces will add
to the dropout voltage of the regulator. The SENSE pin bias
current is 600 A at the nominal rated output voltage. The
SENSE pin can be pulled below ground (as in a dual supply
system where the regulator load is returned to a negative
supply) and still allow the device to start and operate.
ADJ: Adjust. For the adjustable LT1963, this is the input to
the error amplifier. This pin is internally clamped to 7V.
It has a bias current of 3 A which flows into the pin. The
ADJ pin voltage is 1.21V referenced to ground and the
output voltage range is 1.21V to 20V.
SHDN: Shutdown. The SHDN pin is used to put the LT1963
regulators into a low power shutdown state. The output
U
U
U
P
) of PC traces
will be off when the SHDN pin is pulled low. The SHDN pin
can be driven either by 5V logic or open-collector logic
with a pull-up resistor. The pull-up resistor is required to
supply the pull-up current of the open-collector gate,
normally several microamperes, and the SHDN pin cur-
rent, typically 3 A. If unused, the SHDN pin must be
connected to V
shutdown state if the SHDN pin is not connected.
IN: Input. Power is supplied to the device through the IN
pin. A bypass capacitor is required on this pin if the device
is more than six inches away from the main input filter
capacitor. In general, the output impedance of a battery
rises with frequency, so it is advisable to include a bypass
capacitor in battery-powered circuits. A bypass capacitor
in the range of 1 F to 10 F is sufficient. The LT1963 regu-
lators are designed to withstand reverse voltages on the IN
pin with respect to ground and the OUT pin. In the case of
a reverse input, which can happen if a battery is plugged
in backwards, the device will act as if there is a diode in
series with its input. There will be no reverse current flow
into the regulator and no reverse voltage will appear at the
load. The device will protect both itself and the load.
V
IN
+
Figure 1. Kelvin Sense Connection
IN
. The device will be in the low power
IN
SHDN
LT1963
GND
SENSE
OUT
LT1963 Series
R
R
P
P
+
1963 F01
LOAD
1963fa
9