AD9516-0_07 AD [Analog Devices], AD9516-0_07 Datasheet - Page 13
AD9516-0_07
Manufacturer Part Number
AD9516-0_07
Description
14-Output Clock Generator with Integrated 2.8 GHz VCO
Manufacturer
AD [Analog Devices]
Datasheet
1.AD9516-0_07.pdf
(84 pages)
- Current page: 13 of 84
- Download datasheet (2Mb)
Parameter
TIMING
PD, SYNC, AND RESET PINS
Table 15.
Parameter
INPUT CHARACTERISTICS
RESET TIMING
SYNC TIMING
LD, STATUS, REFMON PINS
Table 16.
Parameter
OUTPUT CHARACTERISTICS
MAXIMUM TOGGLE RATE
ANALOG LOCK DETECT
REF1, REF2, AND VCO FREQUENCY STATUS MONITOR
LD PIN COMPARATOR
Clock Rate (SCLK, 1/t
Pulse Width High, t
Pulse Width Low, t
SDIO to SCLK Setup, t
SCLK to SDIO Hold, t
SCLK to Valid SDIO and SDO, t
CS to SCLK Setup and Hold, t
CS Minimum Pulse Width High, t
Output Voltage High (V
Output Voltage Low (V
Capacitance
Normal Range
Extended Range (REF1 and REF2 Only)
Trip Point
Hysteresis
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Capacitance
Pulse Width Low
Pulse Width Low
LO
HI
DH
SCLK
DS
OL
OH
)
)
)
Min
2.0
50
1.5
S
, t
DV
H
PWH
Typ
110
2
Max
0.8
1
Min
16
16
2
1.1
2
3
Unit
V
V
μA
μA
pF
ns
High speed clock cycles
Min
2.7
1.02
8
Typ
Rev. 0 | Page 13 of 84
Typ
100
3
1.6
260
Max
25
8
Max
0.4
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
Unit
V
V
MHz
pF
MHz
kHz
V
mV
Test Conditions/Comments
These pins each have a 30 kΩ internal pull-up resistor
High speed clock is CLK input signal
Test Conditions/Comments
Test Conditions/Comments
When selected as a digital output (CMOS); there are other
modes in which these pins are not CMOS digital outputs;
see Table 53, 0x17, 0x1A, and 0x1B
Applies when mux is set to any divider or counter output,
or PFD up/down pulse; also applies in analog lock detect
mode; usually only debug mode; beware that spurs may
couple to output when any of these pins are toggling
On-chip capacitance; used to calculate RC time constant
for analog lock detect readback; use a pull-up resistor
Frequency above which the monitor always indicates the
presence of the reference
Frequency above which the monitor always indicates the
presence of the reference
AD9516-0
Related parts for AD9516-0_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DPG2 EVAL ADAPTER FOR XILINX BOARDS
Manufacturer:
Analog Devices Inc
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
RF Development Tools Sransceiver board for FMC evaluation kit
Manufacturer:
Analog Devices
Part Number:
Description:
Analog Devices: Data Converters: DAC 12-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Analog Devices: Data Converters: DAC 8-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Low-Power Analog Front End with DSP Microcomputer
Manufacturer:
AD [Analog Devices]
Datasheet: