PIC12F1822 MICROCHIP [Microchip Technology], PIC12F1822 Datasheet - Page 304

• Manufacturer Part Number: PIC12F1822
• Description: 8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

PIC12F/LF1822/16F/LF1823
25.4.2
The following bits are used to configure the EUSART
for Synchronous slave operation:
• SYNC = 1
• CSRC = 0
• SREN = 0 (for transmit); SREN = 1 (for receive)
• CREN = 0 (for transmit); CREN = 1 (for receive)
• SPEN = 1
Setting the SYNC bit of the TXSTA register configures the
device for synchronous operation. Clearing the CSRC bit
of the TXSTA register configures the device as a slave.
Clearing the SREN and CREN bits of the RCSTA register
ensures that the device is in the Transmit mode,
otherwise the device will be configured to receive. Setting
the SPEN bit of the RCSTA register enables the
EUSART.
25.4.2.1
The operation of the Synchronous Master and Slave
modes
“Synchronous Master Transmission”), except in the
case of the Sleep mode.
TABLE 25-9:
DS41413A-page 304
BAUDCON
INTCON
PIE1
PIR1
RCSTA
TRISC
TXREG
TXSTA
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used for Synchronous Slave Transmission.
Note 1:
Name
(1)
*
are
Page provides register information.
PIC16F/LF1823 only.
SYNCHRONOUS SLAVE MODE
EUSART Synchronous Slave
Transmit
TMR1GIE
TMR1GIF
ABDOVF
CSRC
SPEN
identical
Bit 7
SUMMARY OF REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE
TRANSMISSION
GIE
—
RCIDL
PEIE
ADIE
ADIF
Bit 6
(see
RX9
TX9
—
Section 25.4.1.3
TMR0IE
TRISC5
SREN
TXEN
RCIE
RCIF
Bit 5
—
EUSART Transmit Data Register
TRISC4
Preliminary
CREN
SYNC
SCKP
INTE
TXIE
Bit 4
TXIF
SSP1IE
SSP1IF
ADDEN
TRISC3
SENDB
BRG16
IOCIE
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
1.
2.
3.
4.
5.
25.4.2.2
1.
2.
3.
4.
5.
6.
7.
8.
Bit 3
The first character will immediately transfer to
the TSR register and transmit.
The second word will remain in TXREG register.
The TXIF bit will not be set.
After the first character has been shifted out of
TSR, the TXREG register will transfer the second
character to the TSR and the TXIF bit will now be
set.
If the PEIE and TXIE bits are set, the interrupt
will wake the device from Sleep and execute the
next instruction. If the GIE bit is also set, the
program will call the Interrupt Service Routine.
Set the SYNC and SPEN bits and clear the
CSRC bit.
Clear the ANSEL bit for the CK pin (if applicable).
Clear the CREN and SREN bits.
If interrupts are desired, set the TXIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
If 9-bit transmission is desired, set the TX9 bit.
Enable transmission by setting the TXEN bit.
If 9-bit transmission is selected, insert the Most
Significant bit into the TX9D bit.
Start
Significant 8 bits to the TXREG register.
TMR0IF
CCP1IE
CCP1IF
TRISC2
BRGH
FERR
Bit 2
transmission
—
Synchronous Slave Transmission
Set-up:
TMR2IE
TMR2IF
TRISC1
OERR
TRMT
WUE
INTF
Bit 1
 2010 Microchip Technology Inc.
by
writing
TMR1IE
TMR1IF
ABDEN
TRISC0
IOCIF
RX9D
TX9D
Bit 0
the
Register
on Page
281*
290
289
125
288
Least
89
90
92