NCP1573D ONSEMI [ON Semiconductor], NCP1573D Datasheet - Page 9

• Manufacturer Part Number: NCP1573D
• Description: Low Voltage Synchronous Buck Controller
• Manufacturer: ONSEMI [ON Semiconductor]

low−voltage buck controller using the V
provides a programmable−delay Power Good function to
indicate when the output voltage is out of regulation.
V
the ESR of the output capacitors. This ramp is proportional
to the AC current through the main inductor and is offset by
the DC output voltage. This control scheme inherently
compensates for variation in either line or load conditions,
since the ramp signal is generated from the output voltage
itself. The V
such as voltage mode control, which generates an artificial
ramp, and current mode control, which generates a ramp
using the inductor current.
output voltage generates both the error signal and the ramp
signal. Since the ramp signal is simply the output voltage, it
is affected by any change in the output, regardless of the
origin of that change. The ramp signal also contains the DC
portion of the output voltage, allowing the control circuit to
drive the main switch from 0% to 100% duty cycle as
required.
COMP
2
The NCP1573 is a simple, synchronous, fixed−frequency,
The V
The V
Control Method
Figure 19. V
2
2
control method uses a ramp signal generated by
control method is illustrated in Figure 19. The
2
Compensation
RAMP
method differs from traditional techniques
THEORY OF OPERATION
2
Slope
Control with Slope Compensation
Signal
Error
−
+
PWM
Amplifier
Error
GATE(H)
GATE(L)
−
+
2
control method. It
APPLICATION INFORMATION
Reference
Output
Voltage
V
Voltage
FB
http://onsemi.com
9
inductor, which causes the V
the duty cycle. Since any variation in inductor current
modifies the ramp signal, as in current mode control, the V
control scheme offers the same advantages in line transient
response.
modifying the ramp signal. A load step immediately changes
the state of the comparator output, which controls the main
switch. The comparator response time and the transition
speed of the main switch determine the load transient
response. Unlike traditional control methods, the reaction
time to the output load step is not related to the crossover
frequency of the error signal loop.
since the transient response is handled by the ramp signal
loop. The main purpose of this ‘slow’ feedback loop is to
provide DC accuracy. Noise immunity is significantly
improved, since the error amplifier bandwidth can be rolled
off at a low frequency. Enhanced noise immunity improves
remote sensing of the output voltage, since the noise
associated with long feedback traces can be effectively
filtered.
there are two independent control loops. A voltage mode
controller relies on the change in the error signal to
compensate for a deviation in either line or load voltage.
This change in the error signal causes the output voltage to
change corresponding to the gain of the error amplifier,
which is normally specified as line and load regulation. A
current mode controller maintains a fixed error signal during
line transients, since the slope of the ramp signal changes in
this case. However, regulation of load transients still requires
a change in the error signal. The V
maintains a fixed error signal for both line and load variation,
since the ramp signal is affected by both line and load.
microprocessors require the output capacitors to have very
low ESR. The resulting shallow slope in the output ripple can
lead to pulse width jitter and variation caused by both random
and synchronous noise. A ramp waveform generated in the
oscillator is added to the ramp signal from the output voltage
0.5 V
A variation in line voltage changes the current ramp in the
A variation in load current will affect the output voltage,
The error signal loop can have a low crossover frequency,
Line and load regulation are drastically improved because
The stringent load transient requirements of modern
Figure 20. Idealized Waveforms
STARTUP
2
t
S
control scheme to compensate
NORMAL OPERATION
2
method of control
V
V
V
GATE(H)
IN
COMP
FB
2