AT90PWM2B-16SE ATMEL [ATMEL Corporation], AT90PWM2B-16SE Datasheet - Page 50
![no-image](/images/no-image-200.jpg)
AT90PWM2B-16SE
Manufacturer Part Number
AT90PWM2B-16SE
Description
8-bit Microcontroller with 8K Bytes In-System Programmable Flash
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT90PWM2B-16SE.pdf
(361 pages)
- Current page: 50 of 361
- Download datasheet (7Mb)
9.1
9.1.1
9.1.2
9.2
50
Internal Voltage Reference
Watchdog Timer
AT90PWM2/3/2B/3B
Voltage Reference Enable Signals and Start-up Time
Voltage Reference Characteristics
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the Reset flags to identify a reset condition, the user should read and then reset
the MCUSR as early as possible in the program. If the register is cleared before another reset
occurs, the source of the reset can be found by examining the reset flags.
AT90PWM2/2B/3/3B features an internal bandgap reference (1.1V). This reference is used for
Brown-out Detection.
a voltage reference for the DAC and/or the ADC, and can also be used as analog input for the
analog comparators. In order to use the internal Vref, it is necessary to configure it thanks to the
REFS1 and REFS0 bits in the ADMUX register and to set an analog feature which requires it.
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
reference is on during the following situations:
1. When the BOD is enabled (by programming the BODLEVEL [2..0] Fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
3. When the ADC is enabled.
4. When the DAC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC or the DAC,
the user must always allow the reference to start up before the output from the Analog Compar-
ator or ADC or DAC is used. To reduce power consumption in Power-down mode, the user can
avoid the three conditions above to ensure that the reference is turned off before entering
Power-down mode.
Table 9-4.
Note:
AT90PWM2/2B/3/3B has an Enhanced Watchdog Timer (WDT). The main features are:
•
•
Symbol
Clocked from separate On-chip Oscillator
3 Operating modes
V
ACBG bit in ACSR).
– Interrupt
– System Reset
t
I
BG
BG
BG
1. Values are guidelines only.
Parameter
Bandgap reference voltage
Bandgap reference start-up time
Bandgap reference current
consumption
Internal Voltage Reference Characteristics
A 2.56V voltage reference is generated thanks to the bandgap
Table
9-4. To save power, the reference is not always turned on. The
Condition
(1)
Min.
Typ.
1.1
40
15
, i
t
Max.
can be used as
4317J–AVR–08/10
Units
µA
µs
V
Related parts for AT90PWM2B-16SE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AT90PWM2B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![at90pwm2](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
At90pwm2 8-bit Avr Microcontroller With 8k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![AT88SC0204CA-SH](/images/no-image3.png)
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![AT88SC0808CA-SH](/images/no-image3.png)
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![AT88SC1616C-SH](/images/no-image3.png)
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![AT25DF161-SH](/images/no-image3.png)
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATMEGA1281V](/images/no-image3.png)
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: