LPC2194HBD64 NXP [NXP Semiconductors], LPC2194HBD64 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
LPC2194HBD64
Manufacturer Part Number
LPC2194HBD64
Description
Single-chip 16/32-bit microcontroller; 256 kB ISP/IAP flash with 10-bit ADC and CAN
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.LPC2194HBD64.pdf
(40 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC2194HBD64
Manufacturer:
NXP
Quantity:
10 000
Company:
Part Number:
LPC2194HBD64,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
LPC2194HBD64/01
Manufacturer:
NXP
Quantity:
5 000
Company:
Part Number:
LPC2194HBD64/01,15
Manufacturer:
Maxim
Quantity:
60
Company:
Part Number:
LPC2194HBD64/01,15
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
LPC2194HBD64/01,15
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
LPC2194_5
Product data sheet
6.7.1 Features
6.7.2 Features added with the Fast GPIO set of registers available on LPC2194/01
6.6 Pin connect block
6.7 General purpose parallel I/O (GPIO) and Fast I/O
Table 3.
[1]
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals. Peripherals should be connected to the appropriate pins
prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any
enabled peripheral function that is not mapped to a related pin should be considered
undefined.
Device pins that are not connected to a specific peripheral function are controlled by the
parallel I/O registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
only
Block
System Control
ADC
CAN
•
•
•
•
•
•
•
•
SSP interface available on LPC2194/01 only.
Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
Fast GPIO registers are relocated to the ARM local bus for the fastest possible I/O
timing, enabling port pin toggling up to 3.5 times faster than earlier LPC2000 devices.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All GPIO registers are byte addressable.
Entire port value can be written in one instruction.
Interrupt sources
Flag(s)
External Interrupt 0 (EINT0)
External Interrupt 1 (EINT1)
External Interrupt 2 (EINT2)
External Interrupt 3 (EINT3)
A/D Converter
1 ORed CAN Acceptance Filter
CAN1 (Tx int, Rx int)
CAN2 (Tx int, Rx int)
CAN3 (Tx int, Rx int)
CAN4 (Tx int, Rx int)
Rev. 05 — 10 December 2007
…continued
Single-chip 16/32-bit microcontroller
LPC2194
© NXP B.V. 2007. All rights reserved.
VIC channel #
14
15
16
17
18
19
20,21
22,23
24,25
26,27
13 of 40