LPC2364FB100 PHILIPS [NXP Semiconductors], LPC2364FB100 Datasheet - Page 11

• Manufacturer Part Number: LPC2364FB100
• Description: Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 3.
LPC2364_66_68_1
Preliminary data sheet
Symbol
P2.9/
U1CONNECT/
RXD2/
EXTIN0
P2.10/EINT0
P2.11/EINT1/
MCIDAT1/
I2STX_CLK
P2.12/EINT2/
MCIDAT2/
I2STX_WS
P2.13/EINT3/
MCIDAT3/
I2STX_SDA
P3.0 to P3.31
P3.25/MAT0.0/
PWM1.2
P3.26/MAT0.1/
PWM1.3
P4.0 to P4.31
P4.28/MAT2.0/
TXD3
P4.29/MAT2.1/
RXD3
TDO
Pin description
Pin
location
64
53
52
51
50
27
26
82
85
1
Type
I/O
O
I
I
I/O
I
I/O
I
O
I/O
I/O
I
O
I/O
I/O
I
O
I/O
I/O
I/O
O
O
I/O
O
O
I/O
I/O
O
O
I/O
O
I
O
…continued
Description
P2.9 — General purpose digital input/output pin.
U1CONNECT — Signal used to switch an external 1.5 kΩ resistor under the software
control. Used with the SoftConnect USB feature.
RXD2 — Receiver input for UART2.
EXTIN0 — External Trigger Input.
P2.10 — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip bootloader to take over
control of the part after a reset.
EINT0 — External interrupt 0 input.
P2.11 — General purpose digital input/output pin.
EINT1 — External interrupt 1 input.
MCIDAT1 — Data line for SD/MMC interface. (LPC2368 only)
I2STX_CLK — Transmit Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I
P2.12 — General purpose digital input/output pin.
EINT2 — External interrupt 2 input.
MCIDAT2 — Data line for SD/MMC interface. (LPC2368 only)
I2STX_WS — Transmit Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I
P2.13 — General purpose digital input/output pin.
EINT3 — External interrupt 3 input.
MCIDAT3 — Data line for SD/MMC interface. (LPC2368 only)
I2STX_SDA — Transmit data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I
Port 3: Port 3 is a 32-bit I/O port with individual direction controls for each bit. The
operation of port 3 pins depends upon the pin function selected via the Pin Connect
block. Pins 0 through 24, and 27 through 31 of this port are not available.
P3.25 — General purpose digital input/output pin.
MAT0.0 — Match output for Timer 0, channel 0.
PWM1.2 — Pulse Width Modulator 1, output 2.
P3.26 — General purpose digital input/output pin.
MAT0.1 — Match output for Timer 0, channel 1.
PWM1.3 — Pulse Width Modulator 1, output 3.
Port 4: Port 4 is a 32-bit I/O port with individual direction controls for each bit. The
operation of port 4 pins depends upon the pin function selected via the Pin Connect
block. Pins 0 through 27, 30, and 31 of this port are not available.
P4.28 — General purpose digital input/output pin.
MAT2.0 — Match output for Timer 2, channel 0.
TXD3 — Transmitter output for UART3.
P4.29 — General purpose digital input/output pin.
MAT2.1 — Match output for Timer 2, channel 1.
RXD3 — Receiver input for UART3.
TDO — Test Data out for JTAG interface.
Rev. 01 — 22 September 2006
2
S-bus specification.
2
S-bus specification.
LPC2364/2366/2368
2
S-bus specification.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Fast communication chip
11 of 48