LPC2364FB100 PHILIPS [NXP Semiconductors], LPC2364FB100 Datasheet - Page 9

• Manufacturer Part Number: LPC2364FB100
• Description: Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 3.
LPC2364_66_68_1
Preliminary data sheet
Symbol
P1.19/CAP1.1
P1.20/PWM1.2/
SCK0
P1.21/PWM1.3/
SSEL0
P1.22/MAT1.0
P1.23/PWM1.4/
MISO0
P1.24/PWM1.5/
MOSI0
P1.25/MAT1.1
P1.26/PWM1.6/
CAP0.0
P1.27/CAP0.1
P1.28/
PCAP1.0/
MAT0.0
P1.29/
PCAP1.1/
MAT0.1
P1.30/V
AD0.4
P1.31/SCK1/
AD0.5
P2.0 to P2.31
BUS
/
Pin description
Pin
location
33
34
35
37
38
40
43
44
45
21
20
36
39
Type
I/O
I
I/O
O
I/O
I/O
O
I/O
I/O
O
I/O
O
I/O
I/O
O
I/O
I/O
O
I/O
O
I
I/O
I
I/O
I
O
I/O
I
O
I/O
I
I
I/O
I/O
I
I/O
…continued
Description
P1.19 — General purpose digital input/output pin.
CAP1.1 — Capture input for Timer 1, channel 1.
P1.20 — General purpose digital input/output pin.
PWM1.2 — Pulse Width Modulator 1, channel 2 output.
SCK0 — Serial clock for SSP0.
P1.21 — General purpose digital input/output pin.
PWM1.3 — Pulse Width Modulator 1, channel 3 output.
SSEL0 — Slave Select for SSP0.
P1.22 — General purpose digital input/output pin.
MAT1.0 — Match output for Timer 1, channel 0.
P1.23 — General purpose digital input/output pin.
PWM1.4 — Pulse Width Modulator 1, channel 4 output.
MISO0 — Master In Slave Out for SSP0.
P1.24 — General purpose digital input/output pin.
PWM1.5 — Pulse Width Modulator 1, channel 5 output.
MOSI0 — Master Out Slave in for SSP0.
P1.25 — General purpose digital input/output pin.
MAT1.1 — Match output for Timer 1, channel 1.
P1.26 — General purpose digital input/output pin.
PWM1.6 — Pulse Width Modulator 1, channel 6 output.
CAP0.0 — Capture input for Timer 0, channel 0.
P1.27 — General purpose digital input/output pin.
CAP0.1 — Capture input for Timer 0, channel 1.
P1.28 — General purpose digital input/output pin.
PCAP1.0 — Capture input for PWM1, channel 0.
MAT0.0 — Match output for Timer 0, channel 0.
P1.29 — General purpose digital input/output pin.
PCAP1.1 — Capture input for PWM1, channel 1.
MAT0.1 — Match output for Timer 0, channel 0.
P1.30 — General purpose digital input/output pin.
V
Note: This signal must be HIGH for USB reset to occur.
AD0.4 — ADC 0, input 4.
P1.31 — General purpose digital input/output pin.
SCK1 — Serial Clock for SSP1.
AD0.5 — ADC 0, input 5.
Port 2: Port 2 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 2 pins depends upon the pin function selected via the Pin Connect
block. Pins 14 through 31 of this port are not available.
BUS
— Indicates the presence of USB bus power.
Rev. 01 — 22 September 2006
LPC2364/2366/2368
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Fast communication chip
9 of 48