MC9S12DJ256 MOTOROLA [Motorola, Inc], MC9S12DJ256 Datasheet - Page 64
![no-image](/images/no-image-200.jpg)
MC9S12DJ256
Manufacturer Part Number
MC9S12DJ256
Description
MC9S12DT256 Device User Guide V03.03
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC9S12DJ256.pdf
(130 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC9S12DJ256B
Manufacturer:
NO
Quantity:
20 000
Part Number:
MC9S12DJ256BCFU
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC9S12DJ256BMFU
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
MC9S12DJ256CCFU
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S12DJ256CCFU
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
MC9S12DJ256CCPV
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S12DJ256CFUE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MC9S12DJ256MPVE
Manufacturer:
Freescale Semiconductor
Quantity:
135
MC9S12DT256 Device User Guide — V03.03
2.3.26 PH2 / KWH2 / SCK1 — Port H I/O Pin 2
PH2 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as serial clock pin SCK of the Serial Peripheral Interface
1 (SPI1).
2.3.27 PH1 / KWH1 / MOSI1 — Port H I/O Pin 1
PH1 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master output (during master mode) or slave input
pin (during slave mode) MOSI of the Serial Peripheral Interface 1 (SPI1).
2.3.28 PH0 / KWH0 / MISO1 — Port H I/O Pin 0
PH0 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master input (during master mode) or slave output
(during slave mode) pin MISO of the Serial Peripheral Interface 1 (SPI1).
2.3.29 PJ7 / KWJ7 / TXCAN4 / SCL — PORT J I/O Pin 7
PJ7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as the transmit pin TXCAN for the Motorola Scalable
Controller Area Network controller 4 (CAN4) or the serial clock pin SCL of the IIC module.
2.3.30 PJ6 / KWJ6 / RXCAN4 / SDA — PORT J I/O Pin 6
PJ6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as the receive pin RXCAN for the Motorola Scalable
Controller Area Network controller 4 (CAN4) or the serial data pin SDA of the IIC module.
2.3.31 PJ[1:0] / KWJ[1:0] — Port J I/O Pins [1:0]
PJ1 and PJ0 are general purpose input or output pins. They can be configured to generate an interrupt
causing the MCU to exit STOP or WAIT mode .
2.3.32 PK7 / ECS / ROMONE — Port K I/O Pin 7
PK7 is a general purpose input or output pin. During MCU expanded modes of operation, this pin is used
as the emulation chip select output (ECS). During MCU normal expanded wide and narrow modes of
operation, this pin is used to enable the Flash EEPROM memory in the memory map (ROMONE). At the
rising edge of RESET, the state of this pin is latched to the ROMON bit.
62