71M6534 MAXIM [Maxim Integrated Products], 71M6534 Datasheet - Page 45
![no-image](/images/no-image-200.jpg)
71M6534
Manufacturer Part Number
71M6534
Description
Exceeds IEC 62053/ANSI C12.20 Standards
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.71M6534.pdf
(132 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71M6534-IGT/F
Manufacturer:
HONEYWELL
Quantity:
10
Company:
Part Number:
71M6534-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Part Number:
71M6534-IGT/F
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
71M6534-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71M6534H-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
71M6534H-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
DIO4 and DIO5 can be configured to implement the EEPROM Interface.
Additionally, if DIO6 and DIO7 are configured as DIO and defined as outputs, they can be used as dedicated
pulse outputs (WPULSE = DIO6, VARPULSE = DIO7) using the DIO_PW and DIO_PV bits. In this case,
DIO6 and DIO7 are under CE control. Similarly, DIO8 and DIO9 can be declared pulse outputs (XPULSE =
DIO8, YPULSE = DIO9).
The PB pin is a dedicated digital input. In addition, if the optical UART is not used, OPT_TX and OPT_RX can
be configured as dedicated DIO pins, DIO1and DIO2, respectively (see
A 3-bit configuration word, I/O RAM register DIO_Rn (0x2009[2:0] through 0x200E[6:4]) can be used for
certain pins (when configured as DIO) to individually assign an internal resource such as an interrupt or a
timer control (DIO_RRX configures the RX pin). This way, DIO pins can be tracked even if they are
configured as outputs. See
Table 43
DIO_R7. If more than one input is connected to the same resource, the resources are combined using a
logical OR.
Rev 2
When driving LEDs, relay coils etc., the DIO pins should sink the current into GNDD (as shown in
Figure
of the internal switch that connects V3P3D to either V3P3SYS or VBAT.
Since the control for DIO_24 through DIO_55 is shared with the control for LCD segments, the firmware
must take care not to disturb the DIO pins when accessing the LCD segments and vice versa. Usually,
this requires reading the I/O RAM register, applying a mask and writing back the modified byte.
Tracking DIO pins configured as outputs is useful for pulse counting without external hardware.
Either the interrupts or the counter/timer clocks can be used to count the pulse outputs, or
interrupt on the CE’s power failure output.
lists the internal resources which can be assigned using DIO_R0 (also called DIO_RPB) through
Sourcing current into or out of DIO pins other than the PB pin, for example with pull-up or pull-
down resistors, should be avoided. Violating this rule will lead to increased quiescent current in
SLEEP and LCD modes.
9, right), not source it from V3P3D (as shown in
Table 43: Selectable Resources using the DIO_Rn Bits
DIO_Rn
Table 39
0
1
2
3
4
5
6
7
for DIO pins available for this option.
None
Reserved
T0 (counter0 clock)
T1 (counter1 clock)
High priority I/O interrupt (INT0 rising)
Low priority I/O interrupt (INT1 rising)
High priority I/O interrupt (INT0 falling)
Low priority I/O interrupt (INT1 falling)
Resource Selected for DIO Pin
Figure
9, left). This is due to the resistance
Section 1.5.6
Optical
Interface).
45