XRT5897IV EXAR [Exar Corporation], XRT5897IV Datasheet
![no-image](/images/no-image-200.jpg)
XRT5897IV
Available stocks
Related parts for XRT5897IV
XRT5897IV Summary of contents
Page 1
... The device requires transformers on both receiver and transmitter sides, and supports both balanced and unbalanced interfaces. ORDERING INFORMATION Part No. XRT5897IV Rev. 1.11 E2001 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 z (510) 668-7000 z FAX (510) 668-7017 D Compliant with ITU--T G.823 Jitter Tolerance Re- quirements D Logical Inputs Accept either 3 ...
Page 2
XRT5897 BLOCK DIAGRAM RTIP7 (69) 1:2 R1 TIP RX INPUT RING R2 RRING7 (68) LOSCNT (73) LOSSEL (38) R3 TTIP7 (89) 2:1 TIP 9.1 TX OUTPUT R4 TRING7 (91) RING 9.1 Receiver Notes D The same type 1:2CT ratio transformer ...
Page 3
PIN CONFIGURATION LOS6 TXPOS6 TXNEG6 TXCLK6 GND TTIP6 V CC TRING6 GND TXPOS7 TXNEG7 TXCLK7 GND TTIP7 V CC TRING7 GND TRING1 V CC TTIP1 GND TXCLK1 TXNEG1 TXPOS1 LOS1 Rev. 1. 100 1 100 LEAD THIN QUAD ...
Page 4
XRT5897 PIN DESCRIPTION Pin # Symbol Type Description 1 RXPOS1 O Receiver 1 Positive Data Out. Positive RZ data output for channel 1. 2 RXNEG1 O Receiver 1 Negative Data Out. Negative RZ data output for channel ...
Page 5
PIN DESCRIPTION (CONT’D) Pin # Symbol Type Description 36 LOS2 O Receiver 2 Loss of Signal. Asserted during LOS condition Digital Supply (+3.3V + 5%). Digital circuitry LOSSEL I Loss of Signal Delay Select. “Hi” selects ...
Page 6
XRT5897 PIN DESCRIPTION (CONT’D) Pin # Symbol Type Description 71 RTIP6 I Receiver 6 Positive Bipolar Input. 72 GND Analog Ground. Receiver channels 4, 5, and 6. 73 LOSCNT I Loss of Signal Timing Clock Input. For user-programmable LOS delay. ...
Page 7
ELECTRICAL CHARACTERISTICS Test Conditions 3.3V 5 Symbol Parameter DC Electrical Characteristics Parameters V Voltage Supply CC Inputs V Input High Level IH V Input Low Level IL Outputs V Output High Level OH V Output ...
Page 8
XRT5897 P Power Consumption 120W C P Power Consumption 120W C Note: Bold face parameters are covered by production test and guaranteed over operating temperature range. Rev. 1.11 1025 1255 mW All 1’s Transmit and Receive 745 945 mW 50% ...
Page 9
ELECTRICAL CHARACTERISTICS Test Conditions 3.3V 5 Symbol Parameter AC Electrical Characteristics V Output Pulse Amplitude TXOUT (R = 75W Output Pulse Amplitude TXOUT (R = 120W Output Pulse Width XPW PN ...
Page 10
XRT5897 Disabling Output Drivers Output drivers may be individually disabled (hi-z output) by either of the following methods. 1. Either connect the transmit data inputs TXPOS and TXNEG for the channel to be disabled to a log source ...
Page 11
TXPOS (n) TXNEG ( TXCLK (n) TXOUT (n) RXIN (n) T5 RPOS (n) RXNEG (n) Rev. 1.11 TSU THO TSU TR TF TXPW T3 VTXOUT Figure 2. Transmit Timing Diagram Figure 3. Receive Timing ...
Page 12
XRT5897 RETURN LOSS SPECIFICATIONS The following transmitter and receiver return loss specifications are based on a typical 1:2CT ratio transformer. Frequency Range 51kHz to 102kHz 102kHz to 2.048MHz 2.048MHz to 3.072MHz Table 3. Transmitter Return Loss Specification Transmit Return Loss ...
Page 13
SYSTEM DESCRIPTION This device is a seven channel E1 transceiver that provides an electrical interface applications. Its unique architecture includes seven receiver circuits that convert ITU G.703 compliant bipolar signals to TTL compatible logic levels. Each receiver includes a LOS ...
Page 14
XRT5897 Transmitters This device contains four identical ITU G.703 compliant transmitters. The output stage of each transmitter is a differential voltage driver. External resistors need to be connected to the primary of output transformer. This is necessary to maintain an ...
Page 15
Transmitter Output Pulse Measurement Figure 1 shows a typical transmit pulse plotted on the template shown in ITU G.703 Figure 15/G.703. The following conditions apply: V =3.30V CC Transmitter output transformer secondary terminated with 120W. All ones signal. Receiver output ...
Page 16
XRT5897 Transmitter Output Return Loss Measurements The following measurements were made with a Wandel and Goltermann SNA--2 Network Analyzer equipped with an RFZ--1 75W Return Loss Bridge. A 75W to 120W impedance matching transformer was used to make the 120W ...
Page 17
The following pictures show typical results of measurements that made over a 50 KHz to 3.5MHz frequency range. Figure 6, shows a return loss better than 20dB at low frequencies that decreases to about 12dB at 3.5MHz. Since the source ...
Page 18
XRT5897 Output Transformer Selection A 1:2 ratio transformer is recommended for both 75W and 120W operation because the transmitter, when equipped with this device, meets both the ITU G.703 output pulse amplitude requirement and, the ETSI return loss specification. Although ...
Page 19
This may be further simplified Figure 10. Equivalent Circuit Where int ext Therefore Req ...
Page 20
XRT5897 100 LEAD THIN QUAD FLAT PACK 76 100 A Seating Plane A 1 Note: The control dimension is the millimeter column Rev. 1.11 ( 1.4 mm, TQFP) Rev. 2. ...
Page 21
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to im- prove design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits de- scribed herein, conveys no ...