AT27BV020-12CC ATMEL Corporation, AT27BV020-12CC Datasheet
AT27BV020-12CC
Related parts for AT27BV020-12CC
AT27BV020-12CC Summary of contents
Page 1
... Commercial and Industrial Temperature Ranges Description The AT27BV020 is a high-performance, low-power, low-voltage 2,097,152-bit one- time programmable read only memory (OTP EPROM) organized as 256K by 8 bits. It requires only one supply in the range of 2.7 to 3.6V in normal read mode operation, making it ideal for fast, portable systems using either regulated or unregulated battery power ...
Page 2
... MHz and V consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 3V. The AT27BV020 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation ...
Page 3
Block Diagram Absolute Maximum Ratings* Temperature Under Bias .................................. -40°C to +85°C Storage Temperature ..................................... -65°C to +125°C Voltage on Any Pin with Respect to Ground .........................................-2.0V to +7.0V Voltage on A9 with Respect to Ground ......................................-2.0V to +14.0V V ...
Page 4
... MHz mA OUT -400 and removed simultaneously with or after expect during programming. The supply current would then be the sum AT27BV020 -12 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 2.7V to 3.6V 2.7V to 3. Preliminary Information Min Max ...
Page 5
... Output float is defined as the point when data is no longer driven. Condition ( after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27BV020 -90 -12 -15 Min Max Min Max Min 90 120 90 120 ...
Page 6
... F (1) Pin Capacitance ( MHz 25°C) Typ OUT Note: Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV020 6 Output Test Load Note 100 pF including jig capacitance. Max Units Conditions ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV020 a 0.1 F capacitor is required across V transients. DC Programming Characteristics 5° 6.5 0.25V Symbol Parameter I Input Load Current LI V Input Low Level ...
Page 8
... Atmel’s 27BV020 Integrated Product Identification Code Codes A0 Manufacturer 0 1 Device Type Note: The AT27BV020 has the same Product Identification Code as the AT27C020. Both are programming compatible. AT27BV020 8 = 13.0 ± 0.25V PP (1) AC Conditions of Test Input Rise and Fall Times Input Pulse Levels ...
Page 9
Rapid Programming Algorithm A 100 s PGM pulse width is used to program. The address is set to the first location raised to 13.0V. Each address is first programmed PP with one 100 s PGM pulse without ...
Page 10
... Plastic Thin Small Outline Package (TSOP 20mm) 32V 32-Lead, Plastic Thin Small Outline Package (VSOP 14mm) AT27BV020 10 Standby Ordering Code 0.02 AT27BV020-90CC AT27BV020-90JC AT27BV020-90TC AT27BV020-90VC 0.02 AT27BV020-90CI AT27BV020-90JI AT27BV020-90TI AT27BV020-90VI 0.02 AT27BV020-12CC AT27BV020-12JC AT27BV020-12TC AT27BV020-12VC 0.02 AT27BV020-12CI AT27BV020-12JI AT27BV020-12TI AT27BV020-12VI 0.02 AT27BV020-15CC AT27BV020-15JC AT27BV020-15TC AT27BV020-15VC 0.02 AT27BV020-15CI AT27BV020-15JI AT27BV020-15TI ...