LTM4601 LINER [Linear Technology], LTM4601 Datasheet - Page 9

no-image

LTM4601

Manufacturer Part Number
LTM4601
Description
12A DC/DC ?Modules with PLL, Output Tracking and Margining
Manufacturer
LINER [Linear Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTM4601AEV
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTM4601AEV#PBF
Manufacturer:
LT
Quantity:
1 150
Part Number:
LTM4601AEV#PBF
Quantity:
119
Company:
Part Number:
LTM4601AEV#PBF
Quantity:
2 600
Part Number:
LTM4601AEV#TRPBF
Manufacturer:
LT
Quantity:
6 190
Part Number:
LTM4601AEV-1
Manufacturer:
LT
Quantity:
218
Part Number:
LTM4601AEY
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTM4601AEY#PBF
Manufacturer:
LT
Quantity:
1 000
Part Number:
LTM4601AEY#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTM4601AHVEY#PBF
Manufacturer:
LT
Quantity:
218
Part Number:
LTM4601AHVIY#PBF
Manufacturer:
LINEAR
Quantity:
20 000
Part Number:
LTM4601AHVMPY
Manufacturer:
LT/凌特
Quantity:
20 000
OPERATIO
Power Module Description
The LTM4601 is a standalone nonisolated switching mode
DC/DC power supply. It can deliver up to 12A of DC output
current with some external input and output capacitors.
This module provides precisely regulated output voltage
programmable via one external resistor from 0.6V
5.0V
application schematic is shown in Figure 18.
The LTM4601 has an integrated constant on-time current
mode regulator, ultralow R
ing speed and integrated Schottky diodes. The typical
switching frequency is 850kHz at full load. With current
mode control and internal feedback loop compensation,
the LTM4601 module has suffi cient stability margins and
good transient performance under a wide range of operat-
ing conditions and with a wide range of output capacitors,
even all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limit. Besides, foldback current limiting is provided in an
overcurrent condition while V
and undervoltage comparators pull the open-drain PGOOD
output low if the output feedback voltage exits a ±10%
window around the regulation point. Furthermore, in an
overvoltage condition, internal top FET Q1 is turned off
DECOUPLI G REQUIRE E TS
SYMBOL
C
C
IN
OUT
DC
over a 4.5V to 20V wide input voltage. The typical
PARAMETER
External Input Capacitor Requirement
(V
External Output Capacitor Requirement
(V
U
U
IN
IN
= 4.5V to 20V, V
= 4.5V to 20V, V
DS(ON)
FB
drops. Internal overvoltage
OUT
OUT
FETs with fast switch-
= 1.5V)
= 1.5V)
W U
CONDITIONS
I
I
OUT
OUT
T
DC
= 12A, 3× 10µF Ceramics
= 12A
A
= 25°C, V
to
and bottom FET Q2 is turned on and held on until the
overvoltage condition clears.
Pulling the RUN pin below 1V forces the controller into its
shutdown state, turning off both Q1 and Q2. At low load
current, the module works in continuous current mode by
default to achieve minimum output voltage ripple.
When DRV
5V linear regulator powers the internal gate drivers. If a
5V external bias supply is applied on the DRV
an effi ciency improvement will occur due to the reduced
power loss in the internal linear regulator. This is especially
true at the higher input voltage range.
The LTM4601 has a very accurate differential remote
sense amplifi er with very low offset. This provides for
very accurate remote sense voltage measurement. The
MPGM pin, MARG0 pin and MARG1 pin are used to sup-
port voltage margining, where the percentage of margin
is programmed by the MPGM pin, and the MARG0 and
MARG1 select margining.
The PLLIN pin provides frequency synchronization of the
device to an external clock. The TRACK/SS pin is used for
power supply tracking and soft-start programming.
IN
= 12V. Use Figure 1 confi guration.
CC
pin is connected to INTV
LTM4601/LTM4601-1
MIN
100
20
TYP
200
30
CC
an integrated
MAX
CC
pin, then
UNITS
9
4601f
µF
µF

Related parts for LTM4601