P110-6000 ETC1 [List of Unclassifed Manufacturers], P110-6000 Datasheet - Page 2

• Manufacturer Part Number: P110-6000
• Description: INTELLIMISTTM Residential Atomizing Humidifier and Control
• Manufacturer: ETC1 [List of Unclassifed Manufacturers]

Humidifier and Filter Installation —
following procedure to install the humidifier and filter:
COLLET
1. Turn off all power to HVAC equipment.
2. The humidifier should be installed on the supply ple-
3. On vertical equipment, allow clearance of the humidi-
num, perferably near the coil. Mounting near the evap-
orative coil, if applicable, will allow any excess
moisture to exit the system via the condensate drain
pan.
fier and related components such as the water filter and
plastic water line, from the exhaust vent.
3.50”
2.75”
Fig. 1 — Humidifier Dimensions
COLLET
C
Humidifer
MODEL: P110-300
LISTED
PLENUM
VERTICAL
EVAPORATOR
N-COIL
FURNACE
U L
DOUBLE
O-RING
PUSH-IN
CONNECTOR
US
3.50”
10.25”
W1
W2
R
C
DOUBLE
O-RING
PUSH-IN
CONNECTOR
1” DIA.
DRAIN PAN
AIRFLOW
PLENUM
Fig. 2 — Mounting Location
Perform the
SPRAYING INTO COIL
SPRAYING ABOVE COIL
AIRFLOW
EVAPORATOR
COIL
HUMIDIFIER
ALTERNATE
LOCATION
DRAIN PANS
PLENUM
VERTICAL
EVAPORATOR
A-COIL
FURNACE
HUMIDIFIER
2
HORIZONTAL
EQUIPMENT
NOTE: The nozzle assembly can still be rotated 360
degrees after tightening.
10. Cut a piece of tubing of correct length to run from the
12. Remove plastic cap from double o-ring push-in con-
13. Remove plastic cap from double o-ring push-in con-
11. The water filter should be cleaned before use. Run at
4. Place the humidifier mounting template on the supply
5. Drill four mounting holes for no. 6 screws on template.
6. Slide plastic locking nut over end of spray nozzle.
7. Route spray nozzle through 1-in. hole in duct. Mount
8. On vertical equipment, if the nozzle is spraying away
9. The water filter mounting bracket is installed below
air duct in the desired mounting location.
Cut or drill 1-in. spray nozzle hole in duct per tem-
plate. Remove template from duct and discard.
Push metal end of spray nozzle into back of humidifier
nozzle connection. Tighten locking nut onto nozzle
connection, locking spray nozzle to humidifier. Turn
locking nut to finger tight, then tighten an additional
1
Overtightening fittings will cause them to crack and
split, which will create water leaks. See Fig. 3.
humidifier to supply air duct using four no. 6 screws
provided.
from the coil, there should be a minimum of three feet
from the nozzle to the top of the plenum. If this is not
available, then point the nozzle of the humidifier
directly into the evaporator coil.
the humidifier. Mount the bracket to the supply duct or
another suitable location using 2 screws provided.
Bracket must be installed in vertical position.
humidifier water intake valve to the top of the water
filter. See Fig. 4.
least 3 gallons of water through the water filter in the
correct direction, until the outlet water appears clear
(not grey or cloudy).
nector on top of water filter. Ensure tube ends are cut
square and push tube into double o-ring push-in con-
nector until a stop is felt. Plastic or copper tube may be
used. To remove tube, hold collet (inner ring) against
connector body and pull.
nector on bottom of humidifier.
/
4
FURNACE
turn with pliers or a wrench. Do not overtighten.
AIRFLOW
HUMIDIFIER
ALTERNATE
LOCATION
MINIMUM OF
3’ REQUIRED FOR
THIS LOCATION