MAS9191AJ MAS [Micro Analog systems], MAS9191AJ Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
MAS9191AJ
Manufacturer Part Number
MAS9191AJ
Description
Single Chip AMPS/ETACS/NAMPS Audio/Data Processor
Manufacturer
MAS [Micro Analog systems]
Datasheet
1.MAS9191AJ.pdf
(36 pages)
FUNCTIONS
◆
SAT detection is active on voice channel in AMPS or
TACS mode (SYS1=0). The supervisory audio tone is
detected with a digital PLL. The detector compares the
received SAT to the given SAT color code (SCC).
When the given SAT is detected the SATDET bit of
register 11
register 13
SATDET will cause the interrupt SATINT. On the voice
◆
The SAT and signaling tone (ST) are sent only on
the voice channel in AMPS or TACS mode
(SYS1=0). The SATEN and STON can be used to
control the SAT and ST transmission. However, the
device will automatically stop transmitting SAT and
ST signals whenever data is being transmitted, even
though SATEN or STON is high. The signaling tone
is 8kHz in ETACS and 10kHz in AMPS. Also, switch
S17 for TX data and switch S18 for ST can be used
to disable the transmission. The switches must be on
during transmission. The control bits for these
switches are located in register 0D
TXDATA and the ST are summed and amplified with
◆
For enabling answering machine functions, the chip
has an internal DTMF receiver. The receiver is in
power down mode after a reset. The DTMFRP bit of
register 07
mode. The receiver has two separate filters for
separation of the low and high frequencies. The
comparator and logic section measures the low and
high frequency periods with an averaging algorithm.
When the valid DTMF tone is detected the external
steering logic output pin EST is set to high. With an
external RC time constant the tone detect time and
tone dropout times can be adjusted. The STGT
input/output pin has an internal comparator and pull-
up and pull-down transistors. When EST is active
and STGT goes from below to above the Vref level
(VDD/2) the STGT is pulled up with an internal
transistor. This causes the STD signal to go high,
which causes the XINT line to become active. At the
same time the detected DTMF tone is stored in
register 04
the EST will go low, which causes the STGT to fall.
When the STGT falls below the Vref level (VDD/2)
the internal logic pulls the input down. The external
RC circuit will filter out very short gaps in the
received DTMF tone. The interrupt caused by the
SAT detection & regeneration
SAT, ST or Data Transmission
DTMF Receiver
HEX
HEX
HEX
HEX
. When the DTMF tone is not present
is on the rising and falling edge of
is set to high. If SATINTEN bit of
controls the receiver power down
SCC1
0
0
1
1
HEX
. The SAT,
SCC0
0
1
0
1
channel the SAT regeneration can be enabled with bit
SATEN of register 14
register 14
Otherwise, the SAT output frequency will follow
received SAT frequency. The block is in power down
mode when the TXSIP (transmit section in power
down) bit is active in register 07
block is in power down mode.
GC8. The gain of the amplifier is -3.75dB...+3.75dB
with 16 steps. The adjustment is made with bits 0..3
of register 0D
filtered with 4th order SC filter F12. The cutoff
frequency of the filter is 19kHz in AMPS, 15kHz in
ETACS and 200Hz in NAMPS (SYS1=1). The gain of
the filter at 1kHz is 0dB. In the NAMPS mode, the
signal is then fed to low pass filter F15, which is a
2nd order RC type filter. After filtering the signal is
summed to the TX audio signal depending on the
state of switch S20. The switch is controlled by bit 6
of register 01
to set these blocks into power down mode.
DTMF detector is cleared by reading status register
10
not read until the next DTMF tone is received, then
the previous tone will be lost. The formula below can
be used to calculate tone present and tone absent
times. By adding diodes to the external circuit the
tone present and tone dropout times can be altered.
If one of the diodes is removed, the absent and
present times are calculated using the parallel
combination of R1 and R2.
HEX
SAT frequency
. If the interrupt is cleared but register 04
invalid code
5970 Hz
6000 Hz
6030 Hz
STGT
EST
HEX
HEX
HEX
Time = R*C ln(V
nominal SAT frequency is generated.
C
R1
. After being amplified the signal is
.Register 07
HEX
. By setting bit NOMSAT of
HEX
DD
/V
HEX
bit AUDIOP is used
REF
STGT
EST
. After a reset the
DA9191A.000
July 31, 1997
)
R1
C
HEX
R2
16
is