AT45DB161E-SSHD2B-T Adesto Technologies, AT45DB161E-SSHD2B-T Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
AT45DB161E-SSHD2B-T
Manufacturer Part Number
AT45DB161E-SSHD2B-T
Description
Flash 16M 2.5-3.6V 85Mhz Serial Flash
Manufacturer
Adesto Technologies
Datasheet
1.AT45DB161E-SHD-B.pdf
(72 pages)
Specifications of AT45DB161E-SSHD2B-T
Rohs
yes
Data Bus Width
8 bit
Memory Type
Data Flash
Memory Size
16 Mbit
Architecture
Flexible, Uniform Erase
Timing Type
Synchronous
Interface Type
SPI
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.5 V
Maximum Operating Current
26 mA
Operating Temperature
- 40 C to + 85 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8
Factory Pack Quantity
4000
12.
Manufacturer and Device ID Read
Identification information can be read from the device to enable systems to electronically query and identify the device
while it is in the system. The identification method and the command opcode comply with the JEDEC Standard for
“Manufacturer and Device ID Read Methodology for SPI Compatible Serial Interface Memory Devices”. The type of
information that can be read from the device includes the JEDEC-defined Manufacturer ID, the vendor-specific
Device ID, and the vendor-specific Extended Device Information.
The Read Manufacturer and Device ID command is limited to a maximum clock frequency of f
devices are capable of operating at very high clock frequencies, applications should be designed to read the
identification information from the devices at a reasonably low clock frequency to ensure that all devices to be used in the
application can be identified properly. Once the identification process is complete, the application can then increase the
clock frequency to accommodate specific Flash devices that are capable of operating at the higher clock frequencies.
To read the identification information, the CS pin must first be asserted and then the opcode 9Fh must be clocked into
the device. After the opcode has been clocked in, the device will begin outputting the identification data on the SO pin
during the subsequent clock cycles. The first byte to be output will be the Manufacturer ID, followed by two bytes of the
Device ID information. The fourth byte output will be the Extended Device Information (EDI) String Length, which will be
01h indicating that one byte of EDI data follows. After the one byte of EDI data is output, the SO pin will go into a
high-impedance state; therefore, additional clock cycles will have no affect on the SO pin and no data will be output. As
indicated in the JEDEC Standard, reading the EDI String Length and any subsequent data is optional.
Deasserting the CS pin will terminate the Manufacturer and Device ID Read operation and put the SO pin into a
high-impedance state. The CS pin can be deasserted at any time and does not require that a full byte of data be read.
Table 12-1. Manufacturer and Device ID Information
Table 12-2. Manufacturer and Device ID Details
Data Type
Manufacturer ID
Device ID (Byte
1)
Device ID (Byte
2)
Byte No.
1
2
3
4
5
Data Type
Manufacturer ID
Device ID (Byte 1)
Device ID (Byte 2)
[Optional to Read] Extended Device Information (EDI) String Length
[Optional to Read] EDI Byte 1
Bit
7
0
0
0
Family Code
Sub Code
Bit
6
0
0
0
Bit
5
0
1
0
JEDEC Assigned Code
Bit
4
1
0
0
Bit
3
1
0
0
Product Variant
Density Code
Bit
2
1
1
0
Bit
1
1
1
0
Bit
0
1
0
0
Adesto AT45DB161E [DATASHEET]
Valu
Hex
1Fh
26h
00h
e
Details
JEDEC code: 0001 1111 (1Fh for Adesto)
Family code:
Density code: 00110 (16-Mbit)
Sub code:
Product variant:00000
CLK
001 (AT45Dxxx Family)
000 (Standard Series)
8782D–DFLASH–11/2012
. Since not all Flash
Value
1Fh
26h
00h
01h
00h
36