GLS85LP1008B-M-C-LFTE (rev. CB1) Greenliant, GLS85LP1008B-M-C-LFTE (rev. CB1) Datasheet
GLS85LP1008B-M-C-LFTE (rev. CB1)
Specifications of GLS85LP1008B-M-C-LFTE (rev. CB1)
Related parts for GLS85LP1008B-M-C-LFTE (rev. CB1)
GLS85LP1008B-M-C-LFTE (rev. CB1) Summary of contents
Page 1
... GBytes of NAND flash in a multi-chip package. It provides complete ATA/IDE hard disk drive functionality in a small package for easy, space-saving mounting to a system mother- board. This makes the GLS85LP1008B NANDrive SSD the ideal data storage solution for mobile and embedded electronic products that require smaller and more reliable storage. ...
Page 2
... ATA standard interfaces; thereby eliminating the need for additional or proprietary software, such as Flash File System (FFS), on the host. The GLS85LP1008B NANDrives provide complete IDE Hard Disk Drive functionality and compati- bility in a 14mm x 24mm LBGA package for easy, space saving mounting to a system mother- board ...
Page 3
... GByte NANDrive GLS85LP1008B General Description Each NANDrive contains an integrated NAND Controller and NAND Flash dies in a LBGA pack- age. Refer to Figure 1 for the NANDrive block diagram. Performance-optimized NANDrive The heart of the NANDrive is the NAND Controller which translates standard ATA signals into flash media data and control signals. The following components contribute to the NANDrive’ ...
Page 4
... NAND Flash The NANDrive family utilize standard NAND Flash for data storage. Because the re-flow process can alter the NANDrive content, do not program the GLS85LP1008B NAND before the reflow pro- cess. Advanced NAND Management Technology Advanced NAND management technology balances the wear on erased blocks with an advanced wear-leveling scheme which provides a minimum of 7 million host write cycles ...
Page 5
... GByte NANDrive GLS85LP1008B Functional Blocks HOST ATA/IDE BUS Figure 1: NANDrive Block Diagram ©2010 Greenliant Systems, Ltd. NAND Controller Embedded MCU Flash File System SRAM Buffer ECC Internal DMA PMU SCI 5 Advance Information NANDrive NAND Flash 1421 B1.0 S71421-02-000 05/10 ...
Page 6
... IORDY V SS DNU DMARQ DNU IORD# INTRQ DMACK GByte NANDrive GLS85LP1008B DNU DNU DNU V DNU DNU DD A2 CS3FX# DNU DNU DNU DNU DNU SS DNU DNU DNU SS V DNU DNU DD DD DNU DNU ...
Page 7
... GByte NANDrive GLS85LP1008B Table 1: Pin Assignments ( Pin No. Symbol 91-LBGA Host Side Interface D15 H8 D14 G9 D13 G8 D12 H7 D11 F9 D10 DMACK# K2 DMARQ J3 CS1FX# L3 CS3FX# L8 CSEL L9 IORD# H2 IOWR# H9 ©2010 Greenliant Systems, Ltd. ...
Page 8
... The WP#/PD# pin can be used for either the Write Protect mode or Power-down mode, but only one mode is active at any time. The Write Protect or Power-down modes can be selected through the host command. The Write Protect mode is the factory default setting. PWR Ground PWR V (3.3V not use GByte NANDrive GLS85LP1008B T1.4 1421 S71421-02-000 05/10 ...
Page 9
... Product GLS85LP1008B-M-C-LFTE Table 4: Supported ATA Modes Products GLS85LP1008B-M-C-LFTE Configurable Write Protect/Power-down Modes The WP#/PD# pin can be used for either Write Protect mode or Power-down mode, but only one mode is active at any time. Either mode can be selected through the host command, Set-WP#/ PD#-Mode ...
Page 10
... Hidden (Read/Write protected). If the zones are not enabled, the data is unprotected (default con- figuration). Password Protection - Requires a customer-unique password to access information within the pro- tected zones. ©2010 Greenliant Systems, Ltd. (SCI) , and SCICLK. Always provide access to the SCI interface in the PCB GByte NANDrive GLS85LP1008B S71421-02-000 05/10 ...
Page 11
... GByte NANDrive GLS85LP1008B Power-on and Brown-out Reset Characteristics Figure 3 and Table 5 detail the Power-on and Brown-out reset characteristics of the GLS85LP1008B Figure 3: Power-on and Brown-out Reset Timing Table 5: Power-on and Brown-out Reset Timing Item V Rise Time DD V Fall Time DD I/O Transfer Function The default operation for the NANDrive is 16-bit ...
Page 12
... Y Y 42H - Y Y 1XH - - - F6H - - - F3H - - - F4H - - - F5H - - - F1H - - - F2H - - - 7XH - - Y EFH B0H C6H - Y - E6H or 99H - - - 8BH GLS85LP1008B 2,5 6,7 2 LBA - ...
Page 13
... GByte NANDrive GLS85LP1008B Table 7: NANDrive Command Set (Continued Command Standby Standby-Immediate Write-Buffer Write-DMA Write-DMA-EXT Write-Multiple Write-Multiple-EXT Write-Sector(s) Write-Sector(s)-EXT Write-Verify Features register The register contains a valid parameter for this command Sector Count register Sector Number register Cylinder registers 6. For the Drive/Head register:Y means both the Drive and Head parameters are used ...
Page 14
... Time required for security erase unit completion 2 Time required for enhanced security erase unit completion 2 Advanced Power Management Level. This always returns 0000H. 2 Reserved 2 Hardware reset result 12 Reserved 8 Maximum user LBA for 48-bit Address feature set 14 8 GByte NANDrive GLS85LP1008B S71421-02-000 05/10 ...
Page 15
... GByte NANDrive GLS85LP1008B Table 8: Identify-Drive Information (Continued Word Default 1 Address Value 104-127 0000H 128 xxxxH 129-159 0000H 160-216 0000H 217 0001H 218-254 0000H 255 bbA5H 1. xxxx = Don’t care. This field is subject to change by the host or the device. 2. bbbb - default value set by controller. The selections could be user programmable. ...
Page 16
... Word 63: Multi-word DMA Transfer Mode This field identifies the multi-word DMA transfer modes supported by the NANDrive and indicates the mode that is currently selected. Only one DMA mode can be selected at any given time. Bit Function ©2010 Greenliant Systems, Ltd. 8 GByte NANDrive 16 GLS85LP1008B S71421-02-000 05/10 ...
Page 17
... GByte NANDrive GLS85LP1008B 15-11 Reserved 10 Multi-word DMA mode 2 selected 1: Multi-word DMA mode 2 is selected and bits 8 and 9 are cleared Multi-word DMA mode 2 is not selected. 9 Multi-word DMA mode 1 selected 1: Multi-word DMA mode 1 is selected and 8 and 10 should be cleared Multi-word DMA mode 1 is not selected. ...
Page 18
... If not 0000H or FFFFH, the device claims compliance with the major version(s) as indicated by bits [6:1] being set to one. Since ATA standards maintain downward compatibility, a device may set more than one bit. GLS85LP1008B supports ATA-1 to ATA-7. Word 81: Minor Version Number If an implementer claims that the revision of the standard they used to guide their implementation does not need to be reported or if the implementation was based upon a standard prior to the ATA- 3 standard, word 81 should be 0000H or FFFFH ...
Page 19
... GByte NANDrive GLS85LP1008B 3 1: Power Management feature set is supported 2 0: Removable Media feature set is not supported 1 1: Security Mode feature set is supported 0 1: SMART feature set is supported Word 83 The values in this word should not be depended on by host implementers. Bit Function 15 0: Provides indication that the features/command sets supported words are not valid ...
Page 20
... The values in this word should not be depended on by host implementers. Bit Function 15 0: Provides indication that the features/command sets supported words are valid 14 1: Provides indication that the features/command sets supported words are valid 13-0 0: Reserved ©2010 Greenliant Systems, Ltd. 8 GByte NANDrive 20 GLS85LP1008B S71421-02-000 05/10 ...
Page 21
... GByte NANDrive GLS85LP1008B Word 88 Bit Function 15 Reserved 14 1: Ultra DMA mode 6 is selected 0: Ultra DMA mode 6 is not selected 13 1: Ultra DMA mode 5 is selected 0: Ultra DMA mode 5 is not selected 12 1: Ultra DMA mode 4 is selected 0: Ultra DMA mode 4 is not selected ...
Page 22
... Device 0 failed diagnostics. 1: Device 0 passed diagnostics. These bits indicate how Device 0 determined the device number: 00: Reserved. 01: A jumper was used. 10: The CSEL signal was used. 11: Some other method was used or the method is unknown. Shall be set to one GByte NANDrive GLS85LP1008B S71421-02-000 05/10 ...
Page 23
... GByte NANDrive GLS85LP1008B 4 Expire 1: Security count has expired and Security Unlock and Security Erase Unit are command aborted until a Power-on reset or hard reset 3 Freeze 1: Security is frozen 2 Lock 1: Security is locked 1 Enable/Disable 1: Security is enabled 0: Security is disabled 0 Capability 1: NANDrive supports security mode feature set ...
Page 24
... Cyl High (5) Cyl Low (4) ©2010 Greenliant Systems, Ltd. Bits [7:3] 00000b 00000b 00001b 00100b 01000b Other 97H or E3H X Drive GByte NANDrive GLS85LP1008B T9.0 1421 -D data bus and the IOCS16 Bits [2:0] 000b 001b 1 mode 1 mode 1 mode N/A T10.1 1421 ...
Page 25
... GByte NANDrive GLS85LP1008B Bit -> 7 Sec Num (3) Sec Cnt (2) Feature (1) This command causes the NANDrive to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero interpreted as a timer count with each count being 5 milliseconds and the automatic Power-down mode is enabled. If the sector count is zero, the auto- matic Power-down mode is also enabled, the timer count is set to 3, with each count being 5 ms ...
Page 26
... The following table summarizes the valid status and error values for the NANDrive command set. ©2010 Greenliant Systems, Ltd 99H or E6H X Drive 8BH X Drive 6EH 44H 72H 50H 55H or AAH 26 8 GByte NANDrive GLS85LP1008B S71421-02-000 05/10 ...
Page 27
... GByte NANDrive GLS85LP1008B Table 11: Error and Status Register Command Check-Power-Mode 2 Execute-Drive-Diagnostic Flush-Cache Flush-Cache-EXT Identify-Drive Idle Idle-Immediate Initialize-Drive-Parameters NOP Read-Buffer Read-DMA Read-DMA-EXT Read-Multiple Read-Multiple-EXT Read-Sector(s) Read-Sector(s)-EXT Read-Verify-Sector(s) Read-Verify-Sector(s)-EXT Recalibrate Security-Disable-Password Security-Erase-Prepare Security-Erase-Unit Security-Freeze-Lock Security-Set-Password Security-Unlock Seek Set-Features Set-Multiple-Mode Set-Sleep-Mode Set-WP#/PD#-Mode ...
Page 28
... SS Ambient Temperature 0°C to +70° GByte NANDrive GLS85LP1008B V V Symbol Conditions V -0.3V min to 4.0V max DD -0 ...
Page 29
... GByte NANDrive GLS85LP1008B Table 16: Capacitance (Ta = 25°C, f=1 MHz, other pins open) Parameter Description 1 C I/O Pin Capacitance I Input Capacitance IN 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. Table 17: Reliability Characteristics Symbol ...
Page 30
... Max 2 -10 20 120 -120 1.75 1.09 -10 -120 2.4 -4 2.4 -8 2.4 -12 Parameter Min Power supply current (T = 0°C to +70°C) A Sleep/Standby/Idle current (T = 0°C to +70° GByte NANDrive GLS85LP1008B Units Conditions Max Min µ Max Max µ ...
Page 31
... GByte NANDrive GLS85LP1008B AC Characteristics V IHT INPUT V ILT AC test inputs are driven at V ‘0’. Measurement reference points for inputs and outputs are V (0 Input rise and fall times (10% DD Figure 4: AC Input/Output Reference Waveforms Appendix Differences Between the Greenliant NANDrive and ATA Specifications ...
Page 32
... NAND Type Version Capacity MByte or GByte Designator Interface Voltage Product Series 1. Environmental suffix “E” denotes non-Pb sol GByte NANDrive GLS85LP1008B non- ball positions (nearest letter code to total ball count of 91) LF= LBGA C = Commercial: 0°C to +70° MLC ...
Page 33
... GByte NANDrive GLS85LP1008B Packaging Diagram CORNER 9 0.40 ±0.05 Figure 5: NANDrive 91-Ball, Low-profile Ball Grid Array (LBGA) Greenliant Package Code: LFT ©2010 Greenliant Systems, Ltd. TOP VIEW 24.0 ±0.1 BOTTOM VIEW 15 ...
Page 34
... Memory sizes denote raw storage capacity; actual usable capacity may be less. Greenliant makes no warranty for the use of its products other than those expressly contained in the Standard Terms and Conditions of Sale which are available on www.greenliant.com. ©2010 Greenliant Systems, Ltd. 8 GByte NANDrive Description 34 GLS85LP1008B Date Jan 2010 Apr 2010 May 2010 S71421-02-000 05/10 ...