NCN6010DTBR2 ON Semiconductor, NCN6010DTBR2 Datasheet
NCN6010DTBR2
Specifications of NCN6010DTBR2
Available stocks
Related parts for NCN6010DTBR2
NCN6010DTBR2 Summary of contents
Page 1
... Units / Rail NCN6010DTBG TSSOP-14* 96 Units / Rail NCN6010DTBR2 TSSOP-14* 2500/Tape & Reel NCN6010DTBR2G TSSOP-14* 2500/Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. ...
Page 2
STOP 2 ENABLE MOD_V 3 V POWER UNIT & LOGIC PWR_ON CLOCK 6 RESET DATA I/O 5 Figure 2. NCN6010 Block Diagram NCN6010 MANAGEMENT GND GND V CC GND I/O ...
Page 3
PIN DESCRIPTIONS Pin Name Type 1 V POWER DD 2 STOP INPUT 3 MOD_V INPUT CC 4 PWR_ON INPUT 5 I/O INPUT 6 CLOCK INPUT 7 RESET INPUT 8 SIM_RST OUTPUT 9 SIM_CLK OUTPUT 10 GND GROUND 11 SIM_I/O 12 ...
Page 4
MAXIMUM RATINGS (Note 1) Rating Power Supply External Card Power Supply and Level Shifter Digital Input Voltage Digital Input Current Digital Input Voltage Digital Input Current Digital Input Voltage Digital Input Current Digital Input Voltage Digital Input Current Digital Output ...
Page 5
POWER SUPPLY SECTION Rating Power Supply Standby Supply Current @ No Input Clock, All Input Logic Load Connected to the SIM Interface. Ground Current 3.0 V, Operating Conditions: DD PWR_ON ...
Page 6
SIM INTERFACE SECTION (Note 7) Rating SIM_VCC = +5 Isim_rst = +200 mA Output RESET Isim_rst = -200 mA Output RESET V OL Output RESET Rise Time @ Cout = 50 pF Output RESET Fall ...
Page 7
Card Supply Charge Pump Converter The NCN6010 device provides three pins to control the operation of the interface as depicted in Table 1. The built-in charge pump converter circuit provides either a 3 5.0 V output voltage ...
Page 8
Power Down Operation The power down mode can be initiated by either the PWR_ON or by the STOP pin condition. In both cases, the communication I/O session is terminated immediately, according to the ISO7816-3 sequence as depicted in Figure 4. ...
Page 9
Level Shifters When the SIM card voltage is either higher or lower than the MPU V supply, the level shifters can be DD reprogrammed to cope with the expected output voltage. When the MPU and the SIM card operate under ...
Page 10
Figure 7. SIM_IO Rise and Fall Time Oscillogram Input Schmitt Triggers All the Logic Input pins have built-in Schmitt trigger circuits to prevent the NCN6010 against uncontrolled operation. The typical dynamic characteristics of the related pins are depicted in Figure ...
Page 11
MOD_V CC When the NCN6010 is programmed in the 5.0 V output voltage, the clocks are activated, switch S5 is disconnected and the output voltage is the result of the C1 charge transfer into the ...
Page 12
It is clear that, with nearly half an ohm of resistance is series with the pure capacitor, the tantalum or the electrolytic type will generate high voltage spikes and poor regulation in the high frequency operating charge pump built into ...
Page 13
The operating waveforms are given in Figure 12 to illustrate the high peak current flowing in the transfer 6.0 V SIM_V Output Voltage CC Load = 10 mA 4 V(C2:2) 2 SEL>> ...
Page 14
NCN6010 ISO7816 http://onsemi.com 14 ...
Page 15
The layout of the PCB is a key parameter to avoid the voltage spikes that could pollute the rest of the system. Figure 16 represents a typical printed circuit lay out, based on the schematic diagram given in Figure 14, ...
Page 16
... Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada ...