BR93L86-W Rohm Semiconductor, BR93L86-W Datasheet - Page 19
![IC EEPROM 16KBIT 2MHZ 8DIP](/photos/7/22/72250/br93l86-w_sml.jpg)
BR93L86-W
Manufacturer Part Number
BR93L86-W
Description
IC EEPROM 16KBIT 2MHZ 8DIP
Manufacturer
Rohm Semiconductor
Datasheet
1.BR93L56RFVM-WTR.pdf
(41 pages)
Specifications of BR93L86-W
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
16K (1K x 16)
Speed
2MHz
Interface
Microwire, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
BR93L86-W
Manufacturer:
ROHM
Quantity:
2 025
© 2011 ROHM Co., Ltd. All rights reserved.
BR93L□□-W Series, 93A□□-WM Series, BR93H□□-WC Series
www.rohm.com
○Selection of resistance value R
The resistance R becomes through current limit resistance at data collision. When through current flows, noises of
power source line and instantaneous stop of power source may occur. When allowable through current is defined as I,
the following relation should be satisfied. Determine allowable current amount in consideration of impedance and so
forth of power source line in set. And insert resistance R, and set the value R to satisfy EEPROM input level VIH/VIL
even under influence of voltage decline owing to leak current and so forth. Insertion of R will not cause any influence
upon basic operations.
(1) Address data A0 = “1” input, dummy bit “0” output timing
(2) DO status READY output timing
Example) When Vcc=5V, VOHM=5V, IOHM=0.4mA, VOLM=5V, IOLM=0.4mA,
(When microcontroller DI/O output is “H”, EEPROM DO outputs “L”, and “H” is input to DI)
・Make the through current to EEPROM 10mA or below.
・See to it that the level VIH of EEPROM should satisfy the following.
(When the microcontroller DI/O is “L”, EEPROM DO output “H”, and “L” is input to DI)
・Set the EEPROM input level VIL so as to satisfy the following.
Fig.85 Circuit at DI, DO direct connection (Microcontroller DI/O “L” output, EEPROM “H” output)
Fig.84 Circuit at DI, DO direct connection (Microcontroller DI/O “H” output, EEPROM “L” output)
Microcontroller
Microcontroller
“H” output
“L” output
∴
From the equation ⑦,
R ≧
R ≧
R ≧ 12.5 [kΩ]
DI/O PORT
DI/O PORT
VOLM
VOHM
IOHM
IOHM
0.4×10
VOHM
IOHM
5
VOHE
VOLE
R
R
-3
DO
DO
DI
DI
・・・⑨
EEPROM
EEPROM
“H” output
“L” output
19/40
From the equation⑧,
∴
Therefore, from the equations ⑨ and ⑩,
∴
R ≧
R ≧
R ≧ 2.2 [kΩ]
R ≧ 12.5 [kΩ]
Conditions
At this moment, if VOLE=0V,
As this moment, VOHE=Vcc
Conditions
・VIHE
・VOLE
・VOHM
・IOHM
・VILE
・VOHE
・VOLM
・IOLM
Vcc – VOLM
2.1×10
5 – 0.4
IOLM
∴
∴
VOHM ≦ VIHE
VOHM ≦ IOHM×R + VOLE
VOHM ≦ IOHM×R
VOLM ≧ VILE
VOLM ≧ VOHE – IOLM×R
VOLM ≧ Vcc – IOLM×R
-3
: EEPROM VIH specifications
: EEPROM VOL specifications
: Microcontroller VOH specifications
: Microcontroller IOH specifications
: EEPROM VIL specifications
: EEPROM VOH specifications
: Microcontroller VOL specifications
: Microcontroller IOL specifications
・・・⑩
R ≧
Vcc – VOLM
VOHM
IOHM
IOLM
・・・⑦
Technical Note
2011.02 - Rev.F
・・・⑧