IS42S16400F-6TL ISSI, Integrated Silicon Solution Inc, IS42S16400F-6TL Datasheet - Page 19

• Manufacturer Part Number: IS42S16400F-6TL
• Description: IC SDRAM 64MBIT 166MHZ 54TSOP
• Manufacturer: ISSI, Integrated Silicon Solution Inc
• Type: SDRAMr

Specifications of IS42S16400F-6TL

• Format - Memory: RAM
• Memory Type: SDRAM
• Memory Size: 64M (4M x 16)
• Speed: 166MHz
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 54-TSOP II
• Organization: 4Mx16
• Density: 64Mb
• Address Bus: 14b
• Access Time (max): 6/5.4ns
• Maximum Clock Rate: 166MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 130mA
• Pin Count: 54
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 166 MHz
• Access Time: 6 ns, 5.4 ns
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Maximum Operating Current: 130 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 706-1075; IS42S16400F-6TL

IS42S16400F
IC42S16400F
OPERATION
BANK/ROW ACTIVATION
Before any READ or WRITE commands can be issued
to a bank within the SDRAM, a row in that bank must be
“opened.” This is accomplished via the ACTIVE command,
which selects both the bank and the row to be activated
(see Activating Specific Row Within Specific Bank).
After opening a row (issuing an ACTIVE command), a READ
or WRITE command may be issued to that row, subject to
the t
the clock period and rounded up to the next whole number
to determine the earliest clock edge after the ACTIVE
command on which a READ or WRITE command can be
entered. For example, a t
125 MHz clock (8ns period) results in 2.5 clocks, rounded
to 3. This is reflected in the following example, which cov-
ers any case where 2 < [t
procedure is used to convert other specification limits from
time units to clock cycles).
A subsequent ACTIVE command to a different row in the
same bank can only be issued after the previous active
row has been “closed” (precharged). The minimum time
interval between successive ACTIVE commands to the
same bank is defined by t
A subsequent ACTIVE command to another bank can be
issued while the first bank is being accessed, which results
in a reduction of total row-access overhead.The minimum
time interval between successive ACTIVE commands to
different banks is defined by t
Integrated Silicon Solution, Inc. — www.issi.com
Rev. A
03/19/08
Example: Meeting t
rcD
specification. Minimum t
COMMAND
rcD
RCD
rc
rcD
.
specification of 20ns with a
rrD
(MIN) when 2 < [t
CLK
(MIN)/t
rcD
.
should be divided by
ck
ACTIVE
] ≤ 3. (The same
T0
RCD
t
NOP
RCD
T1
(min)/t
Activating Specific Row Within Specific Bank
BA0, BA1
A0-A11
CK
NOP
T2
] ≤ 3
CKE
RAS
CAS
CLK
WE
CS
HIGH - Z
READ or
WRITE
T3
DON'T CARE
BANK ADDRESS
ROW ADDRESS
T4
19