W25Q80BVSSIG Winbond Electronics, W25Q80BVSSIG Datasheet - Page 38
![IC FLASH 8MBIT 8SOIC](/photos/7/23/72379/8-soic__5_3mm_width___8-sop__8-soeiaj_sml.jpg)
W25Q80BVSSIG
Manufacturer Part Number
W25Q80BVSSIG
Description
IC FLASH 8MBIT 8SOIC
Manufacturer
Winbond Electronics
Datasheet
1.W25Q80BVSSIG.pdf
(75 pages)
Specifications of W25Q80BVSSIG
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
8M (1M x 8)
Speed
104MHz
Interface
SPI Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
Q4816329
T1015683
T1015683
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
W25Q80BVSSIG
Manufacturer:
Winbond
Quantity:
2 100
Company:
Part Number:
W25Q80BVSSIG
Manufacturer:
WINBOND
Quantity:
192
Part Number:
W25Q80BVSSIG
Manufacturer:
WINBOND/华邦
Quantity:
20 000
9.2.19
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O”, “Fast Read Quad
I/O”, “Word Read Quad I/O” and “Octal Word Read Quad I/O” instructions to provide the highest random
Flash memory access rate with minimum SPI instruction overhead, thus allow true XIP (execute in place)
to be performed on serial flash devices.
M7-0 need to be set by the Dual/Quad I/O Read instructions. M5-4 are used to control whether the 8-bit
SPI instruction code (BBh, EBh, E7h or E3h) is needed or not for the next command. When M5-4 = (1,0),
the next command will be treated same as the current Dual/Quad I/O Read command without needing
the 8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all
commands can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be
used.
9.2.20
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 18.
Since W25Q80BV does not have a hardware Reset pin, so if the controller resets while W25Q80BV is set
to Continuous Mode Read, the W25Q80BV will not recognize any initial standard SPI instructions from
the controller. To address this possibility, it is recommended to issue a Continuous Read Mode Reset
instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
CLK
/CS
IO
IO
IO
IO
Continuous Read Mode Bits (M7-0)
Continuous Read Mode Reset (FFh or FFFFh)
0
1
2
3
Mode 3
Mode 0
Figure 18. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
0
1
for Quad I/O (FFh)
Mode Bit Reset
2
3
4
5
6
- 38 -
Don't Care
Don't Care
Don't Care
7
8
9
10
for Dual I/O (FFFFh)
Mode Bit Reset
11
12
13
14
W25Q80BV
15
Mode 3
Mode 0