MA240026 Microchip Technology, MA240026 Datasheet - Page 18

• Manufacturer Part Number: MA240026
• Description: Daughter Cards & OEM Boards PIC24FJ16MC102 Plug-In Module
• Manufacturer: Microchip Technology

Specifications of MA240026

• Rohs: yes
• Data Bus Width: 16 bit
• Description/function: PIC24F 28 Pin QFN to 100 Pin Plug-in-Module
• Interface Type: I2C, SPI, UART
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3 V to 3.6 V

PIC24FJ16MC101/102
FIGURE 2-1:
2.2.1
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including MCUs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that con-
nects the power supply source to the device, and the
maximum current drawn by the device in the applica-
tion. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
2.3
A low-ESR (< 5 Ohms) capacitor is required on the
V
regulator output voltage. The V
connected to V
4.7 µF and 10 µF, 16V connected to ground. The type
can be ceramic or tantalum. Refer to
“Electrical
information.
The placement of this capacitor should be close to the
V
exceed one-quarter inch (6 mm). Refer to
“On-Chip Voltage Regulator”
DS39997B-page 18
CAP
CAP
Ceramic
V
0.1 µF
DD
R
. It is recommended that the trace length not
C
pin, which is used to stabilize the voltage
R1
CPU Logic Filter Capacitor
Connection (V
TANK CAPACITORS
10 Ω
Tantalum
MCLR
V
V
10 µF
DD
SS
DD
Characteristics”
, and must have a capacitor between
RECOMMENDED
MINIMUM CONNECTION
PIC24F
Ceramic
0.1 µF
CAP
for details.
)
CAP
pin must not be
for
V
V
DD
Section 26.0
Section 23.2
SS
Ceramic
0.1 µF
Ceramic
0.1 µF
additional
Ceramic
0.1 µF
Preliminary
2.4
The
functions:
• Device Reset
• Device programming and debugging
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (V
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
For
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Place the components shown in
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
Note 1: R ≤ 10 kΩ is recommended. A suggested
example,
MCLR
2: R1 ≤ 470Ω will limit any current flowing into
Master Clear (MCLR) Pin
starting value is 10 kΩ. Ensure that the MCLR
pin V
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
V
V
IH
DD
R
pin
JP
and V
C
IH
as
and V
provides
IL
shown
EXAMPLE OF MCLR PIN
CONNECTIONS
specifications are met.
R1
© 2011 Microchip Technology Inc.
IL
IH
specifications are met.
and V
MCLR
in
two
PIC24F
IL
Figure
Figure 2-2
) and fast signal
specific
2-2,
device
within
it
is