M25P80-VMW6TG NUMONYX, M25P80-VMW6TG Datasheet - Page 39

• Manufacturer Part Number: M25P80-VMW6TG
• Description: IC FLASH 8MBIT 75MHZ 8SOIC
• Manufacturer: NUMONYX
• Series: Forté™r

Specifications of M25P80-VMW6TG

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 8M (1M x 8)
• Speed: 75MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Package: 8SO W
• Cell Type: NOR
• Density: 8 Mb
• Architecture: Sectored
• Block Organization: Symmetrical
• Typical Operating Supply Voltage: 3.3 V
• Sector Size: 64KByte x 16
• Timing Type: Synchronous
• Interface Type: Serial-SPI
• Access Time (max): 8ns
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: SOIC W
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 1M
• Supply Current: 8mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: M25P80-VMW6TG; M25P80-VMW6TGTR

10
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the Measurement Conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 10.
Table 11.
Table 12.
1. Output Hi-Z is defined as the point where data out is no longer driven.
Figure 21. AC measurement I/O waveform
Table 13.
1. Sampled only, not 100% tested, at T
Program/Erase Cycles
Data Retention
C
C
Symbol
Symbol
OUT
IN
Symbol
V
T
C
CC
A
Parameter
L
Output capacitance (Q)
Input capacitance (other pins)
Supply voltage
Ambient operating temperature
Load capacitance
Input rise and fall times
Input pulse voltages
Input timing reference voltages
Output timing reference voltages
Operating conditions
AC measurement conditions
Capacitance
Data retention and endurance
Parameter
Grade 3, Autograde 6,
Grade 6
at 55°C
Parameter
0.8V CC
0.2V CC
Input Levels
(1)
Parameter
Condition
A
= 25 °C and a frequency of 20 MHz.
Test condition
V
V
OUT
100,000
20
IN
grade 3
grade 6
Timing Reference Levels
= 0 V
Min.
= 0 V
Input and Output
Min.
0.2V
0.3V
—
—
0.7V CC
0.5V CC
0.3V CC
AI07455
Min.
–40
–40
2.7
Max.
Min.
CC
CC
V
CC
30
to 0.8V
to 0.7V
/ 2
Max.
Cycles per Sector
years
Max.
5
CC
CC
125
3.6
Max.
85
8
6
Unit
Unit
Unit
pF
ns
Unit
°C
°C
V
V
V
pF
pF
V
39/57